StarTurn image gallery

All info relating to the Denford StarTurn CNC lathes

Moderators: Martin, Steve, Mr Magoo

Post Reply
User avatar
Denford Admin
Site Admin
Posts: 3649
Joined: Fri 10 Feb , 2006 12:40 pm
Hardware/Software: Go to User Control Panel > Profile
Enter as much information about your CNC hardware and software as you can - it makes it easier for everyone to know what you're talking about then.
Location: Sunny Brighouse
Contact:
Contact Denford Admin

StarTurn image gallery

Post by Denford Admin » Fri 29 Jan , 2010 15:52 pm

StarTurn image gallery
Attachments
starturn.jpg
starturn.jpg (54.12 KiB) Viewed 17024 times
Top
beeman
Posts: 14
Joined: Sat 29 Dec , 2007 12:30 pm
Hardware/Software: vertical router and mirac lathe
Location: J.C.FREEMAN@BTINTERNET.COM
Contact:
Contact beeman

Re: StarTurn image gallery

Post by beeman » Tue 23 Feb , 2010 2:42 am

Do you have any photos of a Starturn PC, or any info on these. I have just bought one but not yet collected it. It has lathe cam designer 1.1 and it says it comes with "Starturn PC Software Version 2.23" I can find no mention of this on the forums was this similar to VR Turning?. It is a slant bed similar to a novaturn but with a square case.

Kind regards

John
Attachments
starturnpc.jpg
starturnpc.jpg (9.32 KiB) Viewed 17002 times
jcf
Top
User avatar
Denford Admin
Site Admin
Posts: 3649
Joined: Fri 10 Feb , 2006 12:40 pm
Hardware/Software: Go to User Control Panel > Profile
Enter as much information about your CNC hardware and software as you can - it makes it easier for everyone to know what you're talking about then.
Location: Sunny Brighouse
Contact:
Contact Denford Admin

Re: StarTurn image gallery

Post by Denford Admin » Tue 23 Feb , 2010 10:13 am

The bottom 2 links will be relevant manuals to the software that will run your machine:

DOS machine software PLUS Photos and Drawings:
viewtopic.php?t=196
Dos Software free downloads:
https://www.denford.ltd.uk/index.php?opt ... &Itemid=51
Starturn problems:
viewtopic.php?t=1113
Dosbox:
viewtopic.php?t=844
Fanuc OT offline turning Programming manual DOS version PDF:
viewtopic.php?f=15&t=2324
DOS Turning Software Manual:
viewtopic.php?f=15&t=953
Top
User avatar
Denford Admin
Site Admin
Posts: 3649
Joined: Fri 10 Feb , 2006 12:40 pm
Hardware/Software: Go to User Control Panel > Profile
Enter as much information about your CNC hardware and software as you can - it makes it easier for everyone to know what you're talking about then.
Location: Sunny Brighouse
Contact:
Contact Denford Admin

Re: StarTurn image gallery

Post by Denford Admin » Wed 23 Mar , 2011 13:27 pm

This is the Starturn 5 (ST5) where the Novaturn used to be known as the Starturn 6
(How the obviously older Starturn 4 and 8 fit in I don't know :? )
Attachments
Starturn-5.jpg
Starturn PC / Starturn 5
Starturn-5.jpg (103.42 KiB) Viewed 16817 times
Top
User avatar
Denford Admin
Site Admin
Posts: 3649
Joined: Fri 10 Feb , 2006 12:40 pm
Hardware/Software: Go to User Control Panel > Profile
Enter as much information about your CNC hardware and software as you can - it makes it easier for everyone to know what you're talking about then.
Location: Sunny Brighouse
Contact:
Contact Denford Admin

Re: StarTurn image gallery

Post by Denford Admin » Wed 09 May , 2012 13:17 pm

Starturn 8 with BBC micro
Attachments
starturn8-bbc.jpg
starturn8-bbc.jpg (74.95 KiB) Viewed 16519 times
Top
Post Reply

Return to “StarTurn”