Had to disassemle it for the haul down the stairs, a fine opputunity to clean an inspect the bits and pieces
All in all a fine machine, from an techical school in Sweeden
My new lathe
Moderators: Martin, Steve, Mr Magoo
-
Mr. Fischer
- Posts: 3
- Joined: Sat 31 Jul , 2021 17:08 pm
- Hardware/Software: Denford Cyclone TU 150U
BZT PFE 500E
Solidworks
Mastercam
My new lathe
Now this litlle thing has found a new home i my basment
Had to disassemle it for the haul down the stairs, a fine opputunity to clean an inspect the bits and pieces
All in all a fine machine, from an techical school in Sweeden
Had to disassemle it for the haul down the stairs, a fine opputunity to clean an inspect the bits and pieces
All in all a fine machine, from an techical school in Sweeden
- Attachments
-
- IMG_1088.JPG (197.07 KiB) Viewed 11107 times
-
- IMG_1087.JPG (228.83 KiB) Viewed 11107 times
-
- IMG_1086.JPG (227.5 KiB) Viewed 11107 times
-
- IMG_1078.JPG (340.6 KiB) Viewed 11107 times
-
- IMG_1076.JPG (306.11 KiB) Viewed 11107 times
-
- IMG_1073.JPG (246.63 KiB) Viewed 11107 times
-
- IMG_1072.JPG (218.41 KiB) Viewed 11107 times
-
- IMG_1069.JPG (409.06 KiB) Viewed 11107 times
-
- IMG_1063.JPG (257.02 KiB) Viewed 11107 times
-
- IMG_1062.JPG (504.88 KiB) Viewed 11107 times
-
Mr. Fischer
- Posts: 3
- Joined: Sat 31 Jul , 2021 17:08 pm
- Hardware/Software: Denford Cyclone TU 150U
BZT PFE 500E
Solidworks
Mastercam
Re: My new lathe
Lather converted with SZHG control
- Attachments
-
- IMG_1601.JPG (448.64 KiB) Viewed 11104 times
-
- IMG_1600.JPG (362.33 KiB) Viewed 11104 times
-
- IMG_1599.JPG (409.81 KiB) Viewed 11104 times
-
- IMG_1598.JPG (238.36 KiB) Viewed 11104 times
-
- IMG_1597.JPG (213.62 KiB) Viewed 11104 times
-
- IMG_1596.JPG (293.17 KiB) Viewed 11104 times
Re: My new lathe
Really nice project!
Where in Sweden do you live? I live about 50km from Halmstad. Are the old parts for sale? I don´t have the same servo cards, but you might have some useful parts.
How much does the conversion cost?
Where in Sweden do you live? I live about 50km from Halmstad. Are the old parts for sale? I don´t have the same servo cards, but you might have some useful parts.
How much does the conversion cost?
-
Mr. Fischer
- Posts: 3
- Joined: Sat 31 Jul , 2021 17:08 pm
- Hardware/Software: Denford Cyclone TU 150U
BZT PFE 500E
Solidworks
Mastercam
Re: My new lathe
The mascine was from Sweden, im from denmark
Yep the old pats will be for sale soon, computer / CPU, mintcard, IO card, keyboard, encoder, servos, servodriver and PSU
The cost is about 12.000 Dkr.
SZHG controler and releybord, closedloop steppers with driverand psu, Siemens logo to control toolchanger + small bits and pieces
and lots of hours