Door open safety switch does not properly make contact..
yes I have vacuumed it out, yes I blow it out on a regular basis...
I've lost my sense of humor with this mickey mouse design and would like to know if there is a way to improve the safety switch or bypass it all together.
Door Open Safety Switch
Moderators: Martin, Steve, Mr Magoo
-
richard.rouse
- Posts: 9
- Joined: Mon 25 Feb , 2013 20:51 pm
- Hardware/Software: Denford COmpact 1000 pro.
VR CNC Milling 5.49
-
richard.rouse
- Posts: 9
- Joined: Mon 25 Feb , 2013 20:51 pm
- Hardware/Software: Denford COmpact 1000 pro.
VR CNC Milling 5.49
Re: Door Open Safety Switch
given the lack of response that this question / concern has recieved.. I will pass along the poor customer service experience that I have had with Denford with anyone that will listen. Really wishing I had gone with Forrest Scientific at this point... Perhaps they can rebuild the machine for me.
This switch is still faulty... this CNC router is a boat anchor.
This switch is still faulty... this CNC router is a boat anchor.
Re: Door Open Safety Switch
Hi. Can you explain the problem with the switch? There are two sets of contacts one that interlocks the spindle start and the other indicates the switch status.
Is it permanently saying the guard is open?
Does the guard lock with the power off and release as you power on?
What age is the machine? So I can identify the correct circuit diagram.
Is it permanently saying the guard is open?
Does the guard lock with the power off and release as you power on?
What age is the machine? So I can identify the correct circuit diagram.
-
richard.rouse
- Posts: 9
- Joined: Mon 25 Feb , 2013 20:51 pm
- Hardware/Software: Denford COmpact 1000 pro.
VR CNC Milling 5.49
Re: Door Open Safety Switch
serial number is Uo0419. manufactured date is April 2012
Re: Door Open Safety Switch
I can see the machine is a Compact 1000PRO.
Is it permanently saying the guard is open?
Does the guard lock with the power off and release as you power on?
The guard switch locks as the spindle starts. We have had some issues where the contacts of the switch bounce as it locks which then cause the machine to hang up as it thinks its not safe.
There is a software fix that cures this if that was the problem?
Try downloading the current version of VR Milling 5 and install that. It may cure the problem.
https://www.denfordata.com/downloads/VRMilling_V5_63.zip
A description of the exact problem would help.
Is it permanently saying the guard is open?
Does the guard lock with the power off and release as you power on?
The guard switch locks as the spindle starts. We have had some issues where the contacts of the switch bounce as it locks which then cause the machine to hang up as it thinks its not safe.
There is a software fix that cures this if that was the problem?
Try downloading the current version of VR Milling 5 and install that. It may cure the problem.
https://www.denfordata.com/downloads/VRMilling_V5_63.zip
A description of the exact problem would help.
-
Clive
- CNC Apprentice
- Posts: 36
- Joined: Wed 13 Mar , 2013 12:45 pm
- Hardware/Software: Novamill/Mach3
- Location: North Yorkshire
Re: Door Open Safety Switch
Post deleted as posted in wrong thread.
Regards
Clive
It is perfectly possible for a man to be a fool but not to know it. Unless he is married!
Clive
It is perfectly possible for a man to be a fool but not to know it. Unless he is married!
-
richard.rouse
- Posts: 9
- Joined: Mon 25 Feb , 2013 20:51 pm
- Hardware/Software: Denford COmpact 1000 pro.
VR CNC Milling 5.49
Re: Door Open Safety Switch
Problem is in the design of the door switch. It is a hold open switch. The switch itself was cooked. Replaced it with another, at 400 bucks was a little less than thrilled, but that seems to be a theme in my experiences with Denford.. Machine works fine.