Page 1 of 1
TDS 1 LS-Leadscrew drawings
Posted: Wed 03 Apr , 2019 9:26 am
by De-El
Good day,
I posted this over in the downloads section.
viewtopic.php?f=15&t=5707
Just linking to it from here hoping to find the info I am after.
Regards
D
Re: TDS 1 LS-Leadscrew drawings
Posted: Wed 03 Apr , 2019 11:49 am
by rpwilson
ML 105 402 and 403? What parts are they?
Richard
Re: TDS 1 LS-Leadscrew drawings
Posted: Wed 03 Apr , 2019 13:17 pm
by De-El
Richard
ML 105/402 is the 'English'-thread Leadscrew
ML 105/402C is the Metric-thread Leadscrew
ML 105/403 is the Leadscrew collar
Regards
D
Re: TDS 1 LS-Leadscrew drawings
Posted: Wed 03 Apr , 2019 13:36 pm
by Andy B
Leadscrew drawings now uploaded in
this thread - viewtopic.php?f=50&t=2941&p=22970#p22970
Collar drawing was already uploaded in
this pack of scans - https://www.denfordata.com/downloads/for ... 0scans.pdf
If anyone wants to produce a list of the drawings in each of the packs already uploaded, please do so and send it to me so that I can add to the original post and make searching easier.
Andy
Edited to add extra info.
Re: TDS 1 LS-Leadscrew drawings
Posted: Wed 03 Apr , 2019 13:47 pm
by rpwilson
I've got a scanned copy of ML105 400 which is a general arrangement of the leadscrew, the collar and the support brackets if thats any help, at least it show how they fit together. Is it the metric leadscrew or the imperial one you need? They will be the same except that one will have an 8TPI thread and the other will have a 3mm pitch thread.
At times like this, Ebay is your friend for parts.
Richard
Re: TDS 1 LS-Leadscrew drawings
Posted: Wed 03 Apr , 2019 13:59 pm
by Andy B
Just uploaded ML105/400 too - same post as the leadscrews
Andy
Re: TDS 1 LS-Leadscrew drawings
Posted: Wed 03 Apr , 2019 20:14 pm
by De-El
Thank you so much Andy.
This helps me a lot.
I did go through the pack of scans already, unfortunately ML105/403 is not in there. But it looks like a very simple part I can derive from the arrangement drawing, ML105/400, and make my own if the original drawing is not available. I just want to try and stick as close to the original as possible were I can.
Regards
D
Re: TDS 1 LS-Leadscrew drawings
Posted: Wed 03 Apr , 2019 21:14 pm
by Andy B
De-El wrote: ↑Wed 03 Apr , 2019 20:14 pm
I did go through the pack of scans already, unfortunately ML105/403 is not in there.
Yes it is - on page 23.
It must have been out of sequence when the pile was scanned - between ML105/306 and ML105/307.
Andy
Re: TDS 1 LS-Leadscrew drawings
Posted: Thu 04 Apr , 2019 7:17 am
by De-El
Andy B wrote: ↑Wed 03 Apr , 2019 21:14 pm
De-El wrote: ↑Wed 03 Apr , 2019 20:14 pm
I did go through the pack of scans already, unfortunately ML105/403 is not in there.
Yes it is - on page 23.
It must have been out of sequence when the pile was scanned - between ML105/306 and ML105/307.
Andy
Oops, sorry I didn't notice that, I see it is there yes.
Thank you.
D