Triac PC I/O wiring schematics

All info relating to the Denford Triac series of CNC milling machines

Moderators: Martin, Steve, Mr Magoo

Post Reply
Benny
CNC Expert
CNC Expert
Posts: 201
Joined: Fri 20 Oct , 2006 15:27 pm
Location: USA

Triac PC I/O wiring schematics

Post by Benny » Sun 12 Apr , 2009 0:50 am

Customer looking for Triac PC I/O wiring schematics. Please post to forum. Thank you.
Top
User avatar
Denford Admin
Site Admin
Posts: 3649
Joined: Fri 10 Feb , 2006 12:40 pm
Hardware/Software: Go to User Control Panel > Profile
Enter as much information about your CNC hardware and software as you can - it makes it easier for everyone to know what you're talking about then.
Location: Sunny Brighouse
Contact:
Contact Denford Admin

Post by Denford Admin » Tue 14 Apr , 2009 10:10 am

viewtopic.php?t=2040
Top
jsheets
Posts: 9
Joined: Mon 23 Apr , 2007 18:40 pm

TRIAC RS232 cable

Post by jsheets » Mon 20 Apr , 2009 17:27 pm

I downloaded the ZIP file with the pin out diagram, but I do not understand what pin 5 (five) is supposed to do. I looks like it is connected to pins 2 and 3.

Please clarify.

Thanks,
Jim
Top
Martin
CNC Guru
CNC Guru
Posts: 1916
Joined: Fri 24 Feb , 2006 17:09 pm
Location: Brighouse

Post by Martin » Mon 20 Apr , 2009 23:02 pm

Pins 1,2,3 & 5 are all Automatic Toolchanger (ATC) inputs.

Pin 1 = Arm in.
Pin 2 = Arm out.
Pin 3 = Arm up.
Pin 5 = Arm down.

The common for all the switches is pin 44 (Grnd).
Top
jsheets
Posts: 9
Joined: Mon 23 Apr , 2007 18:40 pm

TRIAC RS232 cable pin out

Post by jsheets » Tue 21 Apr , 2009 12:40 pm

The RS232 cable wiring diagram shows pin out of pins 2 and 3 going from the 9pin connector to pins 3 and 2 of the 25 pin connector. Pin 5 on the 9 pin connector is shown looping around pins 2 and 3. This is what is confusing me. What's up with pin 5 on the 9 pin connector? Also pin 7 on the 25 pin connector loops around pins 3 and 2 of the 25 pin connector.

Thnaks, Jim
Top
User avatar
Steve
CNC Guru
CNC Guru
Posts: 1451
Joined: Tue 21 Feb , 2006 16:15 pm
Location: Denford UK

Post by Steve » Tue 21 Apr , 2009 12:57 pm

Can you put a link to the diagram you are looking at and downloaded?

Pins 2 and 3 are ready transmit and recieve. the next 2 pins ( 4 & 5) are ready to send and ready to recieve.

These pins may not be used and in which case they would be linked to the ground.

Attach the link se we know what you are refering to.
Top
jsheets
Posts: 9
Joined: Mon 23 Apr , 2007 18:40 pm

Post by jsheets » Tue 21 Apr , 2009 13:52 pm

The wiring diagram for the RS 232 cable for a TRIAC is found at location listed below:


https://www.denford.ltd.uk/index.php?opt ... &Itemid=52 and select "cable diagram zip

Thanks Jim[/img]
Top
Martin
CNC Guru
CNC Guru
Posts: 1916
Joined: Fri 24 Feb , 2006 17:09 pm
Location: Brighouse

Post by Martin » Tue 21 Apr , 2009 16:48 pm

Are you looking at the SCREENING?

Most RS232 leads are made using screened cable with the screen going to one of the pins. Pin 5 is therfore the screen.
Top
User avatar
Denford Admin
Site Admin
Posts: 3649
Joined: Fri 10 Feb , 2006 12:40 pm
Hardware/Software: Go to User Control Panel > Profile
Enter as much information about your CNC hardware and software as you can - it makes it easier for everyone to know what you're talking about then.
Location: Sunny Brighouse
Contact:
Contact Denford Admin

Post by Denford Admin » Wed 22 Apr , 2009 8:42 am

Yep - pin 5 on a 9 way D-type is ground (GND)
pin 7 is GND on a 25 way
Top
Post Reply

Return to “Triac”