Where to buy tools and tool holders for 1988 Triac

All info relating to the Denford Triac series of CNC milling machines

Moderators: Martin, Steve, Mr Magoo

Post Reply
nthorpey
Posts: 4
Joined: Mon 06 Mar , 2006 21:57 pm
Contact:
Contact nthorpey

Where to buy tools and tool holders for 1988 Triac

Post by nthorpey » Wed 26 Apr , 2006 13:24 pm

Need to get some tooling together for my machine.

I need to know what taper is on the back end of tool and if anyone sells them.

Ideally need a small collet chuck, with usual size collets.

drill chuck

small face mill.

many thanks in advance

nick
Top
User avatar
Denford Admin
Site Admin
Posts: 3649
Joined: Fri 10 Feb , 2006 12:40 pm
Hardware/Software: Go to User Control Panel > Profile
Enter as much information about your CNC hardware and software as you can - it makes it easier for everyone to know what you're talking about then.
Location: Sunny Brighouse
Contact:
Contact Denford Admin

Post by Denford Admin » Wed 26 Apr , 2006 14:12 pm

I think the best place to start looking would be www.ebay.co.uk (if you haven't already looked there)

A guy on ebay took a lot of our old stock of collets and chucks etc.. - try him:
https://stores.ebay.co.uk/RDG-Tools-OnLine
I've just been told that the taper is a BT35
Top
shakey j
Posts: 21
Joined: Fri 10 Mar , 2006 20:18 pm
Location: Birmingham UK

Post by shakey j » Wed 26 Apr , 2006 22:28 pm

Denford Admin wrote:I think the best place to start looking would be www.ebay.co.uk (if you haven't already looked there)

A guy on ebay took a lot of our old stock of collets and chucks etc.. - try him:
https://stores.ebay.co.uk/RDG-Tools-OnLine
I've just been told that the taper is a BT35
Are these Rotagrip of Birmingham?
Top
User avatar
Denford Admin
Site Admin
Posts: 3649
Joined: Fri 10 Feb , 2006 12:40 pm
Hardware/Software: Go to User Control Panel > Profile
Enter as much information about your CNC hardware and software as you can - it makes it easier for everyone to know what you're talking about then.
Location: Sunny Brighouse
Contact:
Contact Denford Admin

Post by Denford Admin » Thu 27 Apr , 2006 8:33 am

No - I think they are in Hebden Bridge/Todmorden near us in West Yorks - they have a Halifax phone number
Top
shakey j
Posts: 21
Joined: Fri 10 Mar , 2006 20:18 pm
Location: Birmingham UK

Post by shakey j » Thu 27 Apr , 2006 18:26 pm

Denford Admin wrote:No - I think they are in Hebden Bridge/Todmorden near us in West Yorks - they have a Halifax phone number
OK Thanks.

Nick are you talking about the spindle taper, which I believe is R8, or do you have a quick change holder fitted to the machine (which will have the R8 taper on the back end) if it is the quick change I'm not sure what taper it is but I know where to get the units.
Top
nthorpey
Posts: 4
Joined: Mon 06 Mar , 2006 21:57 pm
Contact:
Contact nthorpey

Post by nthorpey » Thu 27 Apr , 2006 19:58 pm

thanks for the help:)

Just had a look at the machine properly this afternoon and it is indeed just an R8 taper ! Thats good as i can buy these locally for a very good price through my rep at work.
Top
Post Reply

Return to “Triac”