Orac Corrupt Display

All info relating to the Denford ORAC CNC lathes

Moderators: Martin, Steve, Mr Magoo

Post Reply
Brian_S
Posts: 6
Joined: Fri 03 Apr , 2009 14:06 pm
Contact:
Contact Brian_S

Orac Corrupt Display

Post by Brian_S » Wed 22 Jul , 2009 1:39 am

Hi Guys,

I have a problem with the display on my Orac. It looks like shift is pressed as it were. It's easier to describe in a photo:

Image

I was wondering if anyone has any pointers as to where to start looking. I don't have the schematics for the video board or the processor board, which will make finding this fault a bit of a nightmare. Does anyone have these schematics at all?

Any help greatly appreciated. I tried programming one of the examples, but unfortunately I get an error reported on every page, even pages like mm/inch where I can't really go wrong, so I wonder if this problem is present on a memory bus, thus the input is also being corrrupted. I don't know how it is all hooked up as yet.
Top
User avatar
Denford Admin
Site Admin
Posts: 3642
Joined: Fri 10 Feb , 2006 12:40 pm
Hardware/Software: Go to User Control Panel > Profile
Enter as much information about your CNC hardware and software as you can - it makes it easier for everyone to know what you're talking about then.
Location: Sunny Brighouse
Contact:
Contact Denford Admin

Re: Orac Corrupt Display

Post by Denford Admin » Wed 22 Jul , 2009 10:38 am

These diagrams may help...

viewtopic.php?f=15&t=400&start=0
Top
Brian_S
Posts: 6
Joined: Fri 03 Apr , 2009 14:06 pm
Contact:
Contact Brian_S

Re: Orac Corrupt Display

Post by Brian_S » Wed 22 Jul , 2009 14:21 pm

Hi,

Thank you for the link. I have those diagrams, but it doesn't include schematics of the syntel board or video board. I shall start downloading component datasheets and get the logic analyser out.

Can't wait to get it working properly so that I can run a program on it!

Best Regards,

Brian.
Top
Brian_S
Posts: 6
Joined: Fri 03 Apr , 2009 14:06 pm
Contact:
Contact Brian_S

Re: Orac Corrupt Display

Post by Brian_S » Wed 29 Jul , 2009 2:06 am

Okay, I found the problem. One of the RAM chips on the video board has a bad data bit. As the memory is 4-bit on an 8-bit bus I swapped two of the RAM chips around to absolutely make sure that the RAM chip was duff. I confirmed via the ascii table that bit-5 was the original problem, and when I swapped both RAM chips around, sure enough the bit that is now duff is bit-1. The photo below shows this. Bizarrely I managed to find replacement MCM2114 RAM on eBay! So as soon as that arrives I should have a working display again.

Image

I'm not sure how this will affect the programming problem though.
Top
Brian_S
Posts: 6
Joined: Fri 03 Apr , 2009 14:06 pm
Contact:
Contact Brian_S

Re: Orac Corrupt Display

Post by Brian_S » Mon 03 Aug , 2009 23:46 pm

Okay, fixing the problem with the MCM2114 RAM on the video board fixed both the programming and video display issues. Brilliant! So I have now run my first program and everything worked fine! I'm really looking forward to designing some bits now that everything's fixed.

Interestingly, this must mean that the program pages must be stored in the video ram, so if anyone else stumbles across this thread with the same problem at least you'll know fixing one problem will fix both.

My first program ran fine :)
Image
Top
User avatar
Denford Admin
Site Admin
Posts: 3642
Joined: Fri 10 Feb , 2006 12:40 pm
Hardware/Software: Go to User Control Panel > Profile
Enter as much information about your CNC hardware and software as you can - it makes it easier for everyone to know what you're talking about then.
Location: Sunny Brighouse
Contact:
Contact Denford Admin

Re: Orac Corrupt Display

Post by Denford Admin » Tue 04 Aug , 2009 8:44 am

Good news! Thanks for the info
Top
Post Reply

Return to “Orac”