My new lathe

All info relating to the Denford Cyclone lathes

Moderators: Martin, Steve, Mr Magoo

Post Reply
Mr. Fischer
Posts: 5
Joined: Sat 31 Jul , 2021 17:08 pm
Hardware/Software: Denford Cyclone TU 150U
BZT PFE 500E
Solidworks
Mastercam

My new lathe

Post by Mr. Fischer » Sun 03 Jul , 2022 11:26 am

Now this litlle thing has found a new home i my basment :D

Had to disassemle it for the haul down the stairs, a fine opputunity to clean an inspect the bits and pieces

All in all a fine machine, from an techical school in Sweeden
Attachments
IMG_1088.JPG
IMG_1088.JPG (197.07 KiB) Viewed 4559 times
IMG_1087.JPG
IMG_1087.JPG (228.83 KiB) Viewed 4559 times
IMG_1086.JPG
IMG_1086.JPG (227.5 KiB) Viewed 4559 times
IMG_1078.JPG
IMG_1078.JPG (340.6 KiB) Viewed 4559 times
IMG_1076.JPG
IMG_1076.JPG (306.11 KiB) Viewed 4559 times
IMG_1073.JPG
IMG_1073.JPG (246.63 KiB) Viewed 4559 times
IMG_1072.JPG
IMG_1072.JPG (218.41 KiB) Viewed 4559 times
IMG_1069.JPG
IMG_1069.JPG (409.06 KiB) Viewed 4559 times
IMG_1063.JPG
IMG_1063.JPG (257.02 KiB) Viewed 4559 times
IMG_1062.JPG
IMG_1062.JPG (504.88 KiB) Viewed 4559 times

Mr. Fischer
Posts: 5
Joined: Sat 31 Jul , 2021 17:08 pm
Hardware/Software: Denford Cyclone TU 150U
BZT PFE 500E
Solidworks
Mastercam

Re: My new lathe

Post by Mr. Fischer » Sun 03 Jul , 2022 11:32 am

Lather converted with SZHG control
Attachments
IMG_1601.JPG
IMG_1601.JPG (448.64 KiB) Viewed 4556 times
IMG_1600.JPG
IMG_1600.JPG (362.33 KiB) Viewed 4556 times
IMG_1599.JPG
IMG_1599.JPG (409.81 KiB) Viewed 4556 times
IMG_1598.JPG
IMG_1598.JPG (238.36 KiB) Viewed 4556 times
IMG_1597.JPG
IMG_1597.JPG (213.62 KiB) Viewed 4556 times
IMG_1596.JPG
IMG_1596.JPG (293.17 KiB) Viewed 4556 times

Edis
Posts: 25
Joined: Fri 19 Aug , 2016 7:04 am
Hardware/Software: Harrison TU150U -96

Re: My new lathe

Post by Edis » Sun 03 Jul , 2022 18:45 pm

Really nice project! :D

Where in Sweden do you live? I live about 50km from Halmstad. Are the old parts for sale? I don´t have the same servo cards, but you might have some useful parts.

How much does the conversion cost?

Mr. Fischer
Posts: 5
Joined: Sat 31 Jul , 2021 17:08 pm
Hardware/Software: Denford Cyclone TU 150U
BZT PFE 500E
Solidworks
Mastercam

Re: My new lathe

Post by Mr. Fischer » Fri 08 Jul , 2022 16:58 pm

Edis wrote:
Sun 03 Jul , 2022 18:45 pm
Really nice project! :D

Where in Sweden do you live? I live about 50km from Halmstad. Are the old parts for sale? I don´t have the same servo cards, but you might have some useful parts.

How much does the conversion cost?
The mascine was from Sweden, im from denmark
Yep the old pats will be for sale soon, computer / CPU, mintcard, IO card, keyboard, encoder, servos, servodriver and PSU

The cost is about 12.000 Dkr.
SZHG controler and releybord, closedloop steppers with driverand psu, Siemens logo to control toolchanger + small bits and pieces
and lots of hours :D

Post Reply