Have you tried downloading the file I posted earlier? dome.zip?
It could be somthing you did when importing the DXF.
Search found 1432 matches
- Thu 28 Oct , 2021 13:21 pm
- Forum: QuickTURN 2D Design
- Topic: Cam Wizard not specifying roughing cuts.
- Replies: 13
- Views: 15788
- Wed 27 Oct , 2021 10:05 am
- Forum: Novamill
- Topic: novamill stopped while setting it up for a job.
- Replies: 16
- Views: 19361
Re: novamill stopped while setting it up for a job.
Hi the battery has no function on the board and could simply be removed with no ill effect.
The battery can leak acid and cause problems on the board so cleaning around the terminals may have helped.
The battery can leak acid and cause problems on the board so cleaning around the terminals may have helped.
- Wed 27 Oct , 2021 10:02 am
- Forum: QuickTURN 2D Design
- Topic: Cam Wizard not specifying roughing cuts.
- Replies: 13
- Views: 15788
Re: Cam Wizard not specifying roughing cuts.
Hardware render uses the basic windows graphics card as oposed to advanced graphic driver. I have downloaded the latest version of Quickturn you may want to try this as mine works fine with either angle selected for the turning tip. Had you changed any other values in the tooling? I would also look ...
- Tue 26 Oct , 2021 17:09 pm
- Forum: QuickTURN 2D Design
- Topic: QuickTURN2D v1.34 released 3rd August 2021
- Replies: 2
- Views: 8890
- Tue 26 Oct , 2021 17:05 pm
- Forum: QuickCAM / LaserCAM 2D Design
- Topic: QuickCam 2D Arc Problem
- Replies: 3
- Views: 8644
Re: QuickCam 2D Arc Problem
I would also note that when using a Microturn you should probably have a maximum component length of 40 and diameter of 25
- Tue 26 Oct , 2021 16:51 pm
- Forum: QuickCAM / LaserCAM 2D Design
- Topic: QuickCam 2D Arc Problem
- Replies: 3
- Views: 8644
Re: QuickCam 2D Arc Problem
Hi,
The image shown is for Quick Turn 2D not QuickCAM. QuickTurn software works in diameter mode as does the machine. If you have a radius of 10 then the Z position would be -10 but the X value would be 20.
The image shown is for Quick Turn 2D not QuickCAM. QuickTurn software works in diameter mode as does the machine. If you have a radius of 10 then the Z position would be -10 but the X value would be 20.
- Tue 26 Oct , 2021 16:48 pm
- Forum: VR Milling - All Versions
- Topic: Comms dropping out
- Replies: 3
- Views: 7504
Re: Comms dropping out
What is the message you get when loosing connection?
Have you checked your PC power saving settings? Make sure the USB is not going into power saving mode.
Have you checked your PC power saving settings? Make sure the USB is not going into power saving mode.
- Thu 21 Oct , 2021 12:54 pm
- Forum: QuickTURN 2D Design
- Topic: Cam Wizard not specifying roughing cuts.
- Replies: 13
- Views: 15788
Re: Cam Wizard not specifying roughing cuts.
Max, There have been a couple of changes in the new version. Check that you have hardware render selected and the part then renders correctly. I have tried processing the file with the standard tooling and with the modified tool angle and both produce the correct roughing stratergy. Could you have c...
- Wed 20 Oct , 2021 17:59 pm
- Forum: QuickTURN 2D Design
- Topic: Cam Wizard not specifying roughing cuts.
- Replies: 13
- Views: 15788
Re: Cam Wizard not specifying roughing cuts.
Hi Max, There apears to be an issue with the DXF DWG import in the version 1.34 that needs to be resolved. The 3D model if not being generated correctly so the profile the tool is trying to follow is incorrect. 1.33 works correctly but has a couple of other issues so I will get our software engineer...
- Wed 20 Oct , 2021 14:13 pm
- Forum: Orac
- Topic: Replacement motors
- Replies: 1
- Views: 6069
Re: Replacement motors
What machine are you running? The router 2600 has always been a 1/4" shaft?
All the steppers are 8 wire motors then connected in either series or parallel. If the motor is driven from the drive denstep then 2 A so series connection if a 4A stepper drive parallel.
All the steppers are 8 wire motors then connected in either series or parallel. If the motor is driven from the drive denstep then 2 A so series connection if a 4A stepper drive parallel.
- Wed 20 Oct , 2021 14:09 pm
- Forum: Novamill
- Topic: novamill stopped while setting it up for a job.
- Replies: 16
- Views: 19361
Re: novamill stopped while setting it up for a job.
SGR is spindle go relay so lights when the spindle is running.
As martin says check the 7 segment as soon as you get a communication issue. It could be going out at that point.
The serial cable is not a standard cabel so you will not be able to buy one.
As martin says check the 7 segment as soon as you get a communication issue. It could be going out at that point.
The serial cable is not a standard cabel so you will not be able to buy one.
- Tue 19 Oct , 2021 12:23 pm
- Forum: QuickTURN 2D Design
- Topic: Cam Wizard not specifying roughing cuts.
- Replies: 13
- Views: 15788
Re: Cam Wizard not specifying roughing cuts.
Hi I tried this with version 1.33.7233.57000 and it all seemed to work OK.
Other than the bar being 34mm I could not see any issues.
What Lathe do you have? Note the max parting diameter on a Turn270 is 25mm Turn 370PRO has 35mm.
Other than the bar being 34mm I could not see any issues.
What Lathe do you have? Note the max parting diameter on a Turn270 is 25mm Turn 370PRO has 35mm.
- Tue 19 Oct , 2021 11:52 am
- Forum: MicroRouter Compact
- Topic: Earth Clamp Mod
- Replies: 11
- Views: 12980
Re: Earth Clamp Mod
Have you checked the power saving settings on your PC? Make sure the USB port does not shut down in power saving mode
Re: Triac ATC
We would have only supplied 6 or 8 station toolholders but no longer supply them for the Triac.
- Tue 19 Oct , 2021 11:40 am
- Forum: Novamill
- Topic: novamill stopped while setting it up for a job.
- Replies: 16
- Views: 19361
Re: novamill stopped while setting it up for a job.
The communications have stopped working. Open the electrical box and check that the Denstep has power. The 7 segment display should be illuminated if not check the 24V fuse.
- Tue 19 Oct , 2021 10:49 am
- Forum: VersaLaser
- Topic: Laser Recharge Warranty
- Replies: 0
- Views: 8898
Laser Recharge Warranty
ULS offer a 12 Month warranty on Recharged Lasers. The terms of the warranty are detailed in the attached document. Universal Laser Systems Limited Warranty (REFURBISHED LASER SOURCE).pdf Universal Laser Systems, Inc. (“ULS”) warrants to the original end user (the “Customer”) of the refurbished lase...
- Fri 24 Sep , 2021 8:39 am
- Forum: QuickCAM / LaserCAM 2D Design
- Topic: QuickCAM License Cost
- Replies: 7
- Views: 11387
Re: QuickCAM License Cost
The small red board shown above is a USB Isolator. These have been fitted to Triacs to prevent damage to the control card in the case of the spindle flashing over to earth. If the motor has had a stall and has flashed over internally then some of the earth current will travel to earth through the US...
- Fri 24 Sep , 2021 8:30 am
- Forum: Denford Classifieds
- Topic: BT35 Toolholders
- Replies: 8
- Views: 11390
Re: BT35 Toolholders
BT 35 is not a taper used on Denford Milling machines. The Triac and VMC have a BT30 taper.
- Fri 24 Sep , 2021 8:29 am
- Forum: Denford Classifieds
- Topic: Triac ATC
- Replies: 3
- Views: 7556
Re: Triac ATC
The toolholders for the Triac are BT30
- Fri 03 Sep , 2021 11:45 am
- Forum: Software
- Topic: Can Software Licences be transfered?
- Replies: 0
- Views: 11219
Can Software Licences be transfered?
As each Software Product is personalised by the Registration Disk contained in it, such a transfer can only be performed under the following conditions: This can only be done by the registered owner of the software. You must transfer all of the Software Product, except your personalised Registration...