Search found 1445 matches
- Tue 15 Oct , 2024 17:17 pm
- Forum: VMC 1300
- Topic: VMC 1300 Pro spindle fails to rotate
- Replies: 3
- Views: 1302
Re: VMC 1300 Pro spindle fails to rotate
The Bernstien Guard switch contacts sometimes bounce when the solenoid locks. This is generally the case with older switches and we made a change to the software to try and minimise this. The guard switch type has varied over the years and the earlier switches had contacts rated for higher currents ...
- Mon 07 Oct , 2024 15:24 pm
- Forum: Software
- Topic: Machine Troubleshooting Help !!!!
- Replies: 3
- Views: 1434
Re: Machine Troubleshooting Help !!!!
There is not much there that is Denford origional equipment.
Unfortunatley unless anyone recognises the control card fitted we will not be able to help.
Unfortunatley unless anyone recognises the control card fitted we will not be able to help.
- Mon 07 Oct , 2024 15:19 pm
- Forum: Micromill / Microturn
- Topic: Micro Turn Pro
- Replies: 2
- Views: 736
Re: Micro Turn Pro
On the software install menu there is an option to veiw or download the manual for the machine
- Mon 07 Oct , 2024 15:11 pm
- Forum: Cyclone
- Topic: FSSB Error?
- Replies: 3
- Views: 996
Re: FSSB Error?
Have you got a backup of the machien parameters?
When the battery went flat you may have lost all the parameters which could include the drive paramiters.
When the battery went flat you may have lost all the parameters which could include the drive paramiters.
- Tue 01 Oct , 2024 13:40 pm
- Forum: Micromill / Microturn
- Topic: Round 7 pin port
- Replies: 3
- Views: 1318
Re: Round 7 pin port
Hi It is a Robot port. If the machine is being supplied to the USA a QM plug will be fitted. Test Procedure for Robot Port: 1. Fit link between A and B on the QM plug 2. Run the QM test program “QM TEST” 3. When the M62 is active Measure on Ohms across C and D for continuity. Check also that LED2 an...
Re: Novaturn
Hi George,
It is normal for the motors to run hot, the axes motors are energised while stationary to hold position and the turret motor is constantly holding the turret disk in position so this is not a problem.
The expanded code says X12430 so this would be a move out of limits.
It is normal for the motors to run hot, the axes motors are energised while stationary to hold position and the turret motor is constantly holding the turret disk in position so this is not a problem.
The expanded code says X12430 so this would be a move out of limits.
- Tue 13 Aug , 2024 14:06 pm
- Forum: Micromill / Microturn
- Topic: Micromill 2000(scantech rebrand)
- Replies: 4
- Views: 3319
Re: Micromill 2000(scantech rebrand)
Hi If you download the latest software for the machine you will find the machine manual on the download that may be helpful.
https://www.denfordata.com/downloads/VR ... _32_CD.zip
https://www.denfordata.com/downloads/VR ... _32_CD.zip
- Tue 13 Aug , 2024 13:57 pm
- Forum: Machines
- Topic: Carriage stop question
- Replies: 1
- Views: 1067
Re: Carriage stop question
Can I ask you repost this in the Vicerory section? You would be more likely to get a responce from another owner.
- Thu 11 Jul , 2024 13:10 pm
- Forum: Electronics
- Topic: DEN 404 Distribution Board Fuses
- Replies: 1
- Views: 4040
Re: DEN 404 Distribution Board Fuses
DEN 2020 Controller
- Thu 11 Jul , 2024 13:06 pm
- Forum: Electronics
- Topic: DEN 404 Distribution Board Fuses
- Replies: 1
- Views: 4040
DEN 404 Distribution Board Fuses
DEN 404C Distribution Board
This card is the base layer of the DEN 2020 Controller.
This card is the base layer of the DEN 2020 Controller.
- Mon 20 May , 2024 12:47 pm
- Forum: VMC 1300
- Topic: VMC 1300, adjustment procedure to eliminate play in toolholder collet/spindle/drawbar assembly
- Replies: 7
- Views: 12461
Re: VMC 1300, adjustment procedure to eliminate play in toolholder collet/spindle/drawbar assembly
Can you remove the pullstud from the tool that does not fit correcly and check that it fits to the taper correctly. You should then see it it fits correctly. The bottom of the drawbar should hit the top of the pullstud as you release the tool. This will help a tool release if stuck on the taper. Tig...
- Thu 16 May , 2024 13:44 pm
- Forum: Machines
- Topic: Turn 270M will not home in X
- Replies: 1
- Views: 1478
Re: Turn 270M will not home in X
Hi, Do you have a manual toolpost or an 8 station turret?
When selecting the machine type the Turn270PRO should be selected if a turret and Turn270PROM if a manual tool post.
The machine type dictates the direction of travel when homing.
When selecting the machine type the Turn270PRO should be selected if a turret and Turn270PROM if a manual tool post.
The machine type dictates the direction of travel when homing.
- Thu 16 May , 2024 11:49 am
- Forum: QuickCAM / LaserCAM 2D Design
- Topic: Is it possible to trim lines?
- Replies: 3
- Views: 18248
Re: Is it possible to trim lines?
The trim feature is now standard in V2 of QuickCAM.
You still have to explode objects to be able to trim them.
You still have to explode objects to be able to trim them.
- Tue 14 May , 2024 13:39 pm
- Forum: VMC 1300
- Topic: VMC 1300, adjustment procedure to eliminate play in toolholder collet/spindle/drawbar assembly
- Replies: 7
- Views: 12461
Re: VMC 1300, adjustment procedure to eliminate play in toolholder collet/spindle/drawbar assembly
None of the springs should be flipped they should all be fitted oposing each other and the 10.5 should be standard for all.
- Tue 14 May , 2024 13:35 pm
- Forum: Software
- Topic: VR Milling V5 X axis in wrong direction
- Replies: 3
- Views: 4958
Re: VR Milling V5 X axis in wrong direction
As martin says the files are produces in Quick Cam pro with the back of the car at the left and with the Rotary fixture you have the back of the car on the right. You have to add a mirror in X command to make it cut right to left with the origin on the RH end. If using Car Wizard you can output to t...
- Tue 14 May , 2024 13:29 pm
- Forum: Triac
- Topic: Using TRIAC with America voltage 110V 1ph, or 220V 2ph
- Replies: 2
- Views: 3046
Re: Using TRIAC with America voltage 110V 1ph, or 220V 2ph
The machine was probably supplied with a seperate autotrancformer in a box. this would convert the 110V to 230 or 240V.
- Tue 14 May , 2024 9:20 am
- Forum: F1 / 4x4 / GT Racing In Schools
- Topic: Denford F1 Fixture Parts Description
- Replies: 2
- Views: 14223
Re: Denford F1 Fixture Parts Description
With the introduction of the F1 Model Block made of foam the bore of the billet was reduced to 18mm.
As a result the spiggot is now a smailler dimension
As a result the spiggot is now a smailler dimension
- Wed 27 Mar , 2024 8:05 am
- Forum: Denford Classifieds
- Topic: Denford Nextmove ST USB controller
- Replies: 2
- Views: 4198
Re: Denford Nextmove ST USB controller
Using Easy Upgrader the card can be used for any machine and will update any machine running without a USB port.
Replacing a Denstep controller performance would be much improved.
.
Replacing a Denstep controller performance would be much improved.
.
- Wed 27 Mar , 2024 8:01 am
- Forum: Software
- Topic: Some software questions
- Replies: 1
- Views: 2664
Re: Some software questions
Hi, The machine RS232 cable will be detIle on the forum. I would also check the EPROM version you have in the machine. If the EPROM is for DOS the software can be downloaded for free if the EPROM is for VR Turning you would have to purchase software from Denford. The serial cable for US machines is ...
- Wed 06 Dec , 2023 9:55 am
- Forum: Turn270
- Topic: Tapered thread ?
- Replies: 2
- Views: 12549
Re: Tapered thread ?
Hi,
The Turn270PRO will not cut does not have a command for taper thread cutting.
The spindle only runs in reverse.
The Turn270PRO will not cut does not have a command for taper thread cutting.
The spindle only runs in reverse.