Search found 57 matches

by paulmo101
Tue 29 Dec , 2020 17:08 pm
Forum: Viceroy
Topic: VBiceroy 1.1 TDS GB Pulley size for vfd conversion
Replies: 12
Views: 12940

Re: VBiceroy 1.1 TDS GB Pulley size for vfd conversion

Hi Thanks for the replies. I have now fitted the Newton Tesla AV750 motor and controller and I`m very pleased with my initial results. Torque and speed control seem very good. I decided to keep the step pulleys and it seems to work well and this will give me plenty of options with the vfd as well an...
by paulmo101
Sun 13 Dec , 2020 15:05 pm
Forum: Viceroy
Topic: VBiceroy 1.1 TDS GB Pulley size for vfd conversion
Replies: 12
Views: 12940

Re: VBiceroy 1.1 TDS GB Pulley size for vfd conversion

Hi Richard Thanks again for the reply. I only tend to take cuts of up to about 1mm but I noticed initially it struggled around that point and slowly got worse. I have heard people say that can take 3 or 4 mm cuts on a viceroy no problem !!! Dont think I`ll be trying that any time soon. I have gone f...
by paulmo101
Sun 13 Dec , 2020 11:42 am
Forum: Viceroy
Topic: VBiceroy 1.1 TDS GB Pulley size for vfd conversion
Replies: 12
Views: 12940

Re: VBiceroy 1.1 TDS GB Pulley size for vfd conversion

Hi Richard

Forgot to say - the speed chart looks great I shall certainly do the same as its very useful. As you said I would imagine you can set your belt some where in the mid range then use the VFD most of the time so eliminating a lot of belt changes.

Thanks again

Paul
by paulmo101
Sun 13 Dec , 2020 11:38 am
Forum: Viceroy
Topic: VBiceroy 1.1 TDS GB Pulley size for vfd conversion
Replies: 12
Views: 12940

Re: VBiceroy 1.1 TDS GB Pulley size for vfd conversion

Hi Richard Thanks for the reply and offer of help. As you say the pic angle looked like it was cover the motor bay door but I understand where you`ve put it now. Hoping my order will be here before Christmas as it will give me an excuse to stop eating and drinking whilst having a play with this proj...
by paulmo101
Sat 12 Dec , 2020 19:31 pm
Forum: Viceroy
Topic: VBiceroy 1.1 TDS GB Pulley size for vfd conversion
Replies: 12
Views: 12940

Re: VBiceroy 1.1 TDS GB Pulley size for vfd conversion

Hi Richard I`ve just had another look at your pics as I was wondering where to mount the control box for the VFD. I notice yours looks to be over the motor door - do you have to remove it to access the motor - just thinking of if you need to change the belt position ? I have ordered the AV750 with t...
by paulmo101
Sat 12 Dec , 2020 18:46 pm
Forum: Viceroy
Topic: VBiceroy 1.1 TDS GB Pulley size for vfd conversion
Replies: 12
Views: 12940

Re: VBiceroy 1.1 TDS GB Pulley size for vfd conversion

Hi Richard - I have had chance today to have a better look at the current "Hoover" motor that is fitted. Originally I was under the impression that the Newton Tesla motor`s drive shaft would not be long enough to fit the standard 4 + 1 pulley but as you say I think its, hopefully, a straight swap as...
by paulmo101
Fri 11 Dec , 2020 17:59 pm
Forum: Viceroy
Topic: VBiceroy 1.1 TDS GB Pulley size for vfd conversion
Replies: 12
Views: 12940

Re: VBiceroy 1.1 TDS GB Pulley size for vfd conversion

Having re-read a few posts especially Dazz`s post on his conversion it looks like keeping the countershaft maybe the way to go - so any suggestions as to motor pulley diameter to use WITH the countershaft? I`m thinking I could try all of the 4 pulleys on the countershaft to try to get a decent range...
by paulmo101
Fri 11 Dec , 2020 16:09 pm
Forum: Viceroy
Topic: VBiceroy 1.1 TDS GB Pulley size for vfd conversion
Replies: 12
Views: 12940

VBiceroy 1.1 TDS GB Pulley size for vfd conversion

Hi Just wondering if anyone has converted the viceroy 1.1 TDS GB using the newton Tesla kit ? I`m looking at using the new AV750 kit with 1 hp motor and I`m thinking of removing my countershaft as the motor shaft will only carry a single pulley, I think, and I was wondering what diameter pulley woul...
by paulmo101
Tue 10 Jul , 2018 20:05 pm
Forum: Viceroy
Topic: Viceroy tdi`s on ebay
Replies: 0
Views: 3488

Viceroy tdi`s on ebay

Just spotted a guy on ebay making thread dial indicators for viceroy lathes, among others. Think listing has ended but it has contact details. https://www.ebay.co.uk/itm/NEW-WIDER-RANGE-METRIC-Thread-Dial-Indicator-Boxford-Denford-and-other-lathes/232729138710?ssPageName=STRK%3AMEBIDX%3AIT&_trksid=p...
by paulmo101
Sat 03 Jun , 2017 18:37 pm
Forum: Viceroy
Topic: Viceroy TDS 1/1 GB counter shaft pulley sizes?
Replies: 1
Views: 3752

Re: Viceroy TDS 1/1 GB counter shaft pulley sizes?

Okay garage floor it is!!! I was thinking of upgrading the motor and vfd combo as mine is only the 0.75hp motor and seems a little weak when taking off anymore than about 1mm in a single pass. I have the original ( I think) 3 phase hoover motor and a Altivar VFD and I retained the original pulley se...
by paulmo101
Thu 01 Jun , 2017 18:33 pm
Forum: Viceroy
Topic: Viceroy TDS 1/1 GB counter shaft pulley sizes?
Replies: 1
Views: 3752

Viceroy TDS 1/1 GB counter shaft pulley sizes?

Hi Just to save me crawling around on my garage floor does anyone happen to know the pulley sizes on the counter shaft (above the motor, below the headstock) on the 1/1 GB lathe? I presume they are quoted in the overall diameter - NOT the bottom of the groove that the belt sits in? Also if memory se...
by paulmo101
Sun 21 May , 2017 19:47 pm
Forum: Viceroy
Topic: TDS 1/1 GBL Lead Screw Dial
Replies: 11
Views: 9676

Re: TDS 1/1 GBL Lead Screw Dial

Hi Dakes55 not sure if your machine is metric or imperial - I have the metric version. I can sort you a picture of my TDI if that will help? Also search for thread "Another thread cutting calculator" within this forum for some good info and a download spreadsheet with all the clever stuff already so...
by paulmo101
Thu 04 May , 2017 20:17 pm
Forum: Viceroy
Topic: TDS 1/1 Tooling size
Replies: 8
Views: 8481

Re: TDS 1/1 Tooling size

Other good youtube channels with loads of good info - mrpete222 - just posted a 9 part series on building a stuart engine form castings lots of good information on setting parts up in the lathe also keith Rucker posts some good stuff on lathe work. The 4 jaw independent chuck is awkward to setup unt...
by paulmo101
Tue 21 Oct , 2014 19:01 pm
Forum: Viceroy
Topic: My new viceroy lathe
Replies: 40
Views: 34548

Re: My new viceroy lathe

Hi Les

I recently ground up a vertical shear tool as mentioned here:

http://www.metalworkingfun.com/showthread.php?tid=2309

I`ve not had a chance to try it yet but it looks Ok.

Cheers

Paul
by paulmo101
Fri 12 Sep , 2014 16:54 pm
Forum: Viceroy
Topic: My new viceroy lathe
Replies: 40
Views: 34548

Re: My new viceroy lathe

Hi Dazz

Thanks for the info.

I presume the bolt ABOVE the sight glass is the filler?

Do you know the approx capacity and I presume you fill to the top of the sight glass?

Cheers

Paul
by paulmo101
Wed 10 Sep , 2014 20:28 pm
Forum: Viceroy
Topic: My new viceroy lathe
Replies: 40
Views: 34548

Re: My new viceroy lathe

Hi

thanks for the reply
Will have alook when in the garage (workshop) Tomorrow

Paul
by paulmo101
Wed 10 Sep , 2014 18:05 pm
Forum: Viceroy
Topic: My new viceroy lathe
Replies: 40
Views: 34548

Re: My new viceroy lathe

Hi

Where is the gearbox drain plug on the TDS?

Cheers
Paul
by paulmo101
Thu 24 Oct , 2013 19:17 pm
Forum: Viceroy
Topic: Viceroys on Ebay
Replies: 1
Views: 2931

Viceroys on Ebay

Hi Folks Just spotted on ebay a number of plain turning viceroys recently removed form a school. They look quite tidy All at £300 at the moment Glasgow area No connection to me just posted for interest. http://www.ebay.co.uk/itm/Viceroy-Metalworking-Lathe-/131023378668?pt=UK_Home_Garden_PowerTools_S...
by paulmo101
Mon 21 Oct , 2013 20:21 pm
Forum: Viceroy
Topic: Viceroy on Ebay
Replies: 2
Views: 3514

Re: Viceroy on Ebay

Hi Les

That was a fair offer for the steadies - I suppose being a college that just wanted rid of everything.
Lathe could have been a good candidate for CNC conversion at that price?

Cheers

Paul
by paulmo101
Sun 20 Oct , 2013 19:49 pm
Forum: Viceroy
Topic: Viceroy on Ebay
Replies: 2
Views: 3514

Viceroy on Ebay

Hi Spotted on Ebay: http://www.ebay.co.uk/itm/Viceroy-Imperial-Dial-Lathe-3-Phase-/290996213657?pt=UK_Home_Garden_PowerTools_SM&hash=item43c0b9d799#ht_739wt_958 Plain turning viceroy removed from a college complete with BOTH STEADIES and chucks etc. Currently at £250 Looks tidy and is 3 PHase so ide...