Search found 22 matches
- Wed 28 Jul , 2010 19:33 pm
- Forum: ZeroCentre/ZeroTurn/ZeroBore
- Topic: Coolant pump upgrade
- Replies: 1
- Views: 8091
Coolant pump upgrade
I would like to fit a high pressure coolant pump to my zeroturn so I can use a bar puller. Does anyone know the maximum power of the coolant pump motor I can fit to the lathe without having to modify the wiring. Obviously I realise I will probably have to change the overload trip for the motor.
- Sun 22 Nov , 2009 21:14 pm
- Forum: ZeroCentre/ZeroTurn/ZeroBore
- Topic: Zeroturn Fanuc homing fault
- Replies: 4
- Views: 10093
Re: Zeroturn Fanuc homing fault
I powered up the machine with CAN and P pressed and it has now successfully homed. Many thanks for your help.
- Sun 22 Nov , 2009 19:08 pm
- Forum: ZeroCentre/ZeroTurn/ZeroBore
- Topic: Zeroturn Fanuc homing fault
- Replies: 4
- Views: 10093
Re: Zeroturn Fanuc homing fault
I forgot to say I have checked the switch and it appears to work ok. Where there are the two switches and the two blocks to activate the switches, I noticed that the machine goes onto the first double sided ramp where the display reads 0.1???, this is where it stops and says overtravel in Z axis. I'...
- Sun 22 Nov , 2009 17:02 pm
- Forum: ZeroCentre/ZeroTurn/ZeroBore
- Topic: Zeroturn Fanuc homing fault
- Replies: 4
- Views: 10093
Zeroturn Fanuc homing fault
When I try to zero the Z axis on my zeroturn I get a z axis overtravel come up on the screen. The X axis zeros fine. I homed the machine and then set the zero position for the job I was doing. I then needed to change a tool so went to home the machine again (this is the position I use for my tool se...
- Sat 10 Oct , 2009 22:11 pm
- Forum: Triac
- Topic: Controlling an indexer with Fanuc Triac
- Replies: 1
- Views: 2262
Controlling an indexer with Fanuc Triac
I want to control a pneumatic indexer using M-codes from the Aux socket on this machine. The sequence would be signal out, indexer index to next position, signal back to machine to say indexer has indexed and then program continues. The index angle would be set on the indexer. The question is what s...
- Thu 02 Apr , 2009 18:34 pm
- Forum: ZeroCentre/ZeroTurn/ZeroBore
- Topic: Denford Zeroturn Collet chuck spares
- Replies: 1
- Views: 8571
Denford Zeroturn Collet chuck spares
I need to find a new pair of seals for the chuck on my lathe. It is an air operated collet chuck which takes M673 collets. The only identification on it is SZSP42 -032-. I need a pair of seals that go between the stationary ring where the air goes in and the rotating chuck itself. I've tried Crawfor...
- Wed 01 Apr , 2009 22:45 pm
- Forum: Denford Classifieds
- Topic: Zeroturn 3-jaw chuck wanted
- Replies: 0
- Views: 1722
Zeroturn 3-jaw chuck wanted
3-jaw chuck wanted for Zeroturn. Power or manual.
- Sat 31 Jan , 2009 12:25 pm
- Forum: ZeroCentre/ZeroTurn/ZeroBore
- Topic: Zeroturn maintenance instructions
- Replies: 1
- Views: 8323
Zeroturn maintenance instructions
Does any body have a maintenance manual for the zeroturn that I could have a copy of? Or know which bits I should be lubricating?
- Sat 31 Jan , 2009 0:13 am
- Forum: ZeroCentre/ZeroTurn/ZeroBore
- Topic: Not Denford cyclone but zeroturn tailstock pics wanted
- Replies: 0
- Views: 7780
Not Denford cyclone but zeroturn tailstock pics wanted
Seem to have got cyclone on the brain when I wrote the first post because it is actually a zeroturn I have!
- Thu 29 Jan , 2009 19:22 pm
- Forum: Cyclone
- Topic: Denford cyclone tailstock
- Replies: 0
- Views: 2462
Denford cyclone tailstock
Does anyone have a tailstock fitted to their cyclone that they could send me a picture of?
Thanks
Thanks
- Sun 23 Nov , 2008 17:21 pm
- Forum: Machines
- Topic: Another Harrison M280 trainer
- Replies: 7
- Views: 13202
The machine is now displaying on the monitor. When turned on it goes through it's memory checks and the says "previous boot incomplete-start using default mode" then below this it says "keyboard error" and then it restarts itself. I have got another normal keyboard plugged in to the socket in the ba...
- Sat 22 Nov , 2008 19:36 pm
- Forum: Machines
- Topic: Another Harrison M280 trainer
- Replies: 7
- Views: 13202
I turned the machine on again today and the seven bit displayed showed an L. I think the monitor may not be working properly. Is it possible to plug in a normal computer monitor to check? The transformer is meant to give out 110v for the control system and this also feed to the power supply unit for...
- Sat 22 Nov , 2008 13:05 pm
- Forum: Machines
- Topic: Another Harrison M280 trainer
- Replies: 7
- Views: 13202
Another Harrison M280 trainer
I have a 1994 Harrison M280 trainer. When I went to view the machine it was working ok. Now it has been transported and installed in my workshop. On turning the machine on the screen displayed some info on the operating system, then memory check and below that it said previous bootup (i think!) fail...
- Sat 27 Sep , 2008 10:09 am
- Forum: ZeroCentre/ZeroTurn/ZeroBore
- Topic: Zeroturn fanuc displays "NOT READY"
- Replies: 5
- Views: 12592
Thanks for your help. The machine now does something. Next problem!!! When I home the machine the x axis does not read zero! The z axis does read zero and I have cleared all tool offsets and work shift offsets. X did read abot 155mm with a work shift of about 11mm. When I cleared the work shift back...
- Fri 26 Sep , 2008 20:45 pm
- Forum: ZeroCentre/ZeroTurn/ZeroBore
- Topic: Zeroturn fanuc displays "NOT READY"
- Replies: 5
- Views: 12592
Zeroturn fanuc displays "NOT READY"
I have recently bought a Zeroturn with Fanuc control. On powering it up it wouldn't home and kept giving an axis limit overtravel alarm. On powering it up again I held down the CAN and P buttons as advised and now it gives a "not ready" message at the bottom left of the machine and nothing will move...
- Wed 20 Aug , 2008 22:05 pm
- Forum: ZeroCentre/ZeroTurn/ZeroBore
- Topic: DENFORD ZEROTURN ADVICE AND TAILSTOCK QUERY
- Replies: 1
- Views: 8732
DENFORD ZEROTURN ADVICE AND TAILSTOCK QUERY
Does anybody have a tailstock for a zeroturn or dimensions so I can make one? Is the zeroturn a good machine or would I be better going for a cyclone?
- Sat 09 Aug , 2008 9:54 am
- Forum: Triac
- Topic: Is it possible to run a 4th (rotary) axis from a Triac?
- Replies: 4
- Views: 4115
Is it possible to run a 4th (rotary) axis from a Triac?
Is this possible or would the machine need modifications. It has an NUM operating system
- Thu 16 Nov , 2006 0:29 am
- Forum: Cyclone
- Topic: CYCLONE POWER SUPPLY AGAIN.
- Replies: 6
- Views: 6851
- Tue 14 Nov , 2006 17:45 pm
- Forum: Cyclone
- Topic: CYCLONE POWER SUPPLY AGAIN.
- Replies: 6
- Views: 6851
- Fri 10 Nov , 2006 12:54 pm
- Forum: Cyclone
- Topic: CYCLONE POWER SUPPLY AGAIN.
- Replies: 6
- Views: 6851