how do i go about buying one of these

The tool is good in the spindle
It’s the spindle body in the casting because the bearings have loosened because the locking adjusting ring loosens if that makes senses

hi , I have an atc triac probably once a year the spindle bearings works a bit loose and you get a rough finish and can jiggle the tool a bit . I usually just tighten it up and tap down a new tab washer. is this normal as its becoming a pain . or can you recommend a fix so I may not have to do it ag...

any tips or tricks?

my cyclone is cutting on a taper ,ie 24mm at chuck , 24.2 50mm out
it looks like there are m10 bolts holding the spindle body to the casting

allen bolts look fiddle to get to

so any tips for trying to get this to cut parallel

cheers

thank you i had removed them so they were more like the original 7208 bep ,they now run at late 20's deg c .

i mashed my spindle bearings ,they were bep . but i thought i would keep the rubbish out and fitted rs (rubber seal) bearings . ive noticed the casting and spindle is getting hot ,43c i have the angular contact bearings not too tight ,just enough to not wobble. so is the issue with rubber seals and ...

thank you where is the correct oil level ,when you say top of the tube do you mean the top of the 1/2 hole which the hydraulic piston goes in to or higher so it leaks out the side also spring adjustment is there a procedure or length or do i fit a tool and wind the adjuster in until i have enough gr...

thanks i took a punt and bought a 200va transformer all seems good

hi people i need some help before my head explodes.... i have an issue with my triac tool changer ..it has bt30 spindle , the air hydraulic cylinder which pushes down to release the pull stud has about 10mm travel . i presume this is correct. i can wind down the cylinder so it just clears the top of...

i have a modified triac i need to buy an 110v transformer just to run the oiler ....any idea what va 240vto 110v transformer i require

thanks

i have a denford triac , I've designed a part and don't have enough x travel i need around 320mm depending on the cutter i choose.

Has anyone fitted a different table ,upgraded to linear rails ???
any advice appreciated

cheers

hi im looking for advice on a 4th axis to fit to my triac running on mach3. ive seen a load on ebay that look like the stepper holds the chuck in place by a belt ,which looks like itll be jumping around . ive also seen advertised gapless harmonic drive versions which have the same pic as above so im...

Hi
i have a cyclone and i need a tail stock for it . i presume the chances of getting one are slim so has anyone done a mod to fit another one ?

any help or suggestion,s pics of the standard one etc would be appreciated

cheers

thanks

So with these settings i should be in the ball park?
Regarding the parting tool lifting , does this suggest faulty turret with too much play or to be expected if settings are way out ?
thanks

i have a cyclone with a toe80 toolchanger .its all working mach 3. i have a 3mm hss parting tool (ill buy different if advised) i am struggling to part 25mm aluminium with it . its snatching grabbing sounds terrible vibrates . i can see the tool lifting a bit. if something is loose or worn i will fi...

thank you

do you or anyone know the taper on the spindle which locates the backplate for a chuck ?

hi i have a cyclone and i need some external jaws for it ...i cannot see any manufacturer on the chuck just the numbers H13665 its 125mm with 35mm through hole 95mm recess

the jaws have 716 stamped on them

does anyone know what chuck i have and where to get jaws

cheers

So it would be usefull for me to know what the rpm range and pulley ratio were on the original 2.2kw machine Mine is 2.2kw and the spindle will go up to 5000rpm (at least, that's what it says, I have no way to measure, but it looks scary fast!). Pulley ratio looks 1:1 Si this is where i need some c...

Im in the middle of a cyclone conversion to mach3 ,and would be interested if you could tell me if you know the max rpm of the spindle on your machine. and whether its a 2 pole or 4 pole motor and pulley ratio mine has a 1.5kw motor on it , but i have 2 new 2.2kw motors on the shelf one 2 pole, one ...

unfortunately the literature shows 4kw motors motors and no pulley sizes , but i would presume its not a 1:1 ratio to achieve 5000rpm i have seen the cyclone on youtube clearly marked 3700 max rpm so I'm guessing if its 1:1 then that's about 120hz so i need to know max hz to run 4pole 1,5kw 220v 3ph...