do you have any experience with this RH80 tool post.
great to have the schematics. thanks

you can enable them . Do you have 2 screens to do with your tools to set offsets etc.

problem solved it was some settings in the 300 diag that were wrong just not all of them can be changed

Hi do you still have your zero turn and is it 0TB fanuc or 0TC

Hi Again, have just noticed that if i m39 command the door ram operates and i can press the control panel switch to open, but control panel switch will not actuate door closing. This also seems to be the case with the chuck apart from chuck does not fully close. so M11 operates chuck and foot pedal ...

Hi martin, 453 was set 0 have just tried 1 no difference. Is there anyone that would have a copy ? is there any parameter that would give a longer/continuous air blast to the chuck?

Hi Martin, yes have set 450 diagnostics. Ive tried loads of different settings in a vain attempt :( What I have noticed is the foot pedal for the chuck does nothing but program M11 and M10 do partially operate the chuck also the door air ram can only be operated by nc program not with the control pa...

Ok update on problem . Got new eproms and copied data off original 0E1 and 0E2 chips then loaded onto new chips. That worked and loaded all perameters and diagnostics that I assume are the default ones so just had to edit a few to match ones i have for machine. Only problem I have now is air chuck n...

Hi Martin thanks for the info. Still struggling to get the RH80 tool post to work.
could it be the 0E1 and 0E2 eproms that are the problem being from a 0Tc rather than 0Tb with the version being different
would it be possible to get some replacement eproms or the software to put onto new eproms

Hi Martin thanks for the reply.
can you tell me what these actually refer to N0535, N0536, N0705 and N0708 as the ones you have sent me are different to the ones in the manual I have for the lathe

My manual has 535 P35 536 P25 705 P-189000 708 P 160000

thanks

Machine serial number is ZT20049A
serial number for electrics is 8124513

Hi will get number tomorrow. Just a small update it seems the eeproms I change were from 0t c not 0t a as i first thought.

Hi I have a Zeroturn with 6 position tool post and fanuc 0tb, memory fault happened yesterday rom parity 998 e01 and e02 I tried to re input the parameters but it kept failing so I removed the 2 chips and replaced them with ones from a 0ta that i have the boards from. Managed to get all the paramete...

Hi guys my Home button has stopped working today after using the machine to make a couple of parts. Some of the other keys had been poor responding but worked fine eventually but now the home button refuses to respond. I have rebooted twice but still no joy. Any Ideas??

Ok turret now working fully. Turns out there are 2 contactors that operate the tool change cycle c/s 2 and c/s 3
c/s2 was pulling in but c/s3 was not , after manually engaging the c/s3 it now works repeatedly.

Hi Pete, thanks I do recall seeing something on ebay.
Some 25 years ago I actually converted a colchester student cross slide nut and shaft to fit my viceroy and about 6 years
I had to turn up a new spindle as it had worn.
Phil

Hi John did you have any luck finding one?

Just an update from using my machine the enter that I refer to is actually "Input"

Hi what I can hear is the contactor clicking in and then a short while after it drops out. I have also watched this. Strangely went to machine today after not trying for a week or so and before I turned power on I slid the little amp rating sliders on that one and the one to the left of it. Switched...

Hi procedure for tool change in manual mode.
MDI- program- m06 enter-T2(or which ever number you want to go to)enter- cycle. If you have a door normally requires
this to be closed, will come up with error message and will require re typing commands.
hope this helps