Search found 13 matches

by debinyang
Fri 20 Nov , 2009 11:24 am
Forum: Downloads
Topic: Fanuc Fapt Ladder Editor (DOS)
Replies: 1
Views: 27685

Re: Fanuc Fapt Ladder Editor (DOS)

If you use following software you can use any commercial eprom reader/writer to do fanuc
pmc compiler and discompilier
http://www.cncb3h.com/fladder_e.htm
by debinyang
Fri 20 Nov , 2009 11:13 am
Forum: Downloads
Topic: Heidenhain TNC 351- 355 Service Manual
Replies: 2
Views: 11827

Re: Heidenhain TNC 351- 355 Service Manual

:lol: thank you
by debinyang
Mon 15 Jun , 2009 13:44 pm
Forum: Software
Topic: Fapt ladder II request
Replies: 12
Views: 19314

Re: Fapt ladder II request

hi first floor!

may be fanuc 0mb 0mc has two eprom chips. so it's used fapt ladder soware.
ladder ii is used for fanuc power mate d/h,and fanuc 15,16,18.
by debinyang
Thu 11 Jun , 2009 14:05 pm
Forum: Cyclone
Topic: Cyclone Fanuc OT Model B Control RS232 comms
Replies: 6
Views: 14332

In my mind 552 and 553=10 means 4800 baudrate. fanuc 0 has two rs232 ports. they vertical arranged on the board. you can exchange another. normally fanuc only display LSK no input flash. LSK at here means waiting input or now is outputing. because punch and read are two channel in the ic chips, anot...
by debinyang
Thu 11 Jun , 2009 11:13 am
Forum: Orac
Topic: Orac RS232 cable
Replies: 21
Views: 17721

hi cnc guru,
how can i look your correction,you can send to my mail.
ydebin@yahoo.com

if you can correct my web page i'll invide you have dinner tonight in peking.

thanks you very much ,

debin
by debinyang
Thu 11 Jun , 2009 11:04 am
Forum: Orac
Topic: Orac RS232 cable
Replies: 21
Views: 17721

Lone_Ranger point out a very good question. why using xon/xoff cnc happens override. you know normally fanuc cnc allow over transfer 20 characters when meet xoff(13or93 hex code). but some people write communication software like use api or mscomm.dll. if you use api or mscomm.dll the software shoul...
by debinyang
Thu 11 Jun , 2009 10:31 am
Forum: Orac
Topic: Orac RS232 cable
Replies: 21
Views: 17721

thank you CNC guru
by debinyang
Thu 11 Jun , 2009 10:29 am
Forum: Orac
Topic: Orac RS232 cable
Replies: 21
Views: 17721

i' ve comparaed from usb-->rs232 and standard rs232 to transfer a file. usb/rs232 should be lower 30%. perhaps usb/rs232 has through two protocol. one is usb protocol another is rs232. but any way if you use labtop to connect cnc is ok you'd better power off and then take off or plug in the connecto...
by debinyang
Thu 11 Jun , 2009 10:08 am
Forum: Orac
Topic: Orac RS232 cable
Replies: 21
Views: 17721

Desktop computers use +-12V voltage for rs232 ic chips. A Laptop uses single +5v for rs232 ic chips. Inside the ic chips ( for example:max232) it has a dc-dc converter. through +5v to convert into about +- 8V for rs232 voltage demanding. So normally single 5V ic chips overload capability is lower. T...
by debinyang
Wed 10 Jun , 2009 18:02 pm
Forum: Cyclone
Topic: Cyclone Fanuc OT unable to edit /input programs manually
Replies: 7
Views: 6352

1.Normally fanuc protect key is on when you edit a program the system should be alarm. 2.if you like after the panel you can open or shortage the protect button.It will release protect key 3.fanuc mode select switch is md1,md2,md3 signal in diagnostic. you can check the diagnotic bit. sometimes the ...
by debinyang
Wed 10 Jun , 2009 17:42 pm
Forum: Orac
Topic: Orac RS232 cable
Replies: 21
Views: 17721

about cnc dnc

i 'm a new member at here. i want to give you some suggestions. 1. some old cnc system only know hardware protocol 2. many of cnc system know software protocol xon/xoff (11/13 hex code) 3. many software can connecte with cnc system for example:xtalk,procomm,xp terminal 4. when you check cnc communic...
by debinyang
Wed 10 Jun , 2009 16:27 pm
Forum: Software
Topic: Fapt ladder II request
Replies: 12
Views: 19314

fapt ladder eprom w/r converter

if using my converter software you can use general eprom w/r
to process fanuc pmc. ANd need not to use fanuc eprom w/r its too expensive and has to use a transformer from 220v to 100v.
ydebin@yahoo.com

:lol:
by debinyang
Wed 10 Jun , 2009 16:22 pm
Forum: Software
Topic: Fapt ladder II request
Replies: 12
Views: 19314

fapt ladder eprom w/r converter

I wrote two software on dos:
1.convert #ex ---> oe1,oe2 for writing eprom
2.convert oe1,oe2--->#ex for discompile and display ladder
http://www.cncb3h.com ydebin@yahoo.com :lol: