I think this one will help a little, but is there a drawing for how they are connected to the relays. Thanks

I have a Micromill 2000 and I need wiring diagram for ON key and the OFF button (with light). All of the wiring diagrams I have found on this forum do not have ON key and the OFF button (with light) setup, they all have the ON key, but the OFF is the E-Stop button. The off button on my machine would...

I have a 2002 Micromill 2000, and I need to know who makes the spindle drive card, so I can get a wiring diagram for it. Thanks

I guess I will have to try that. Thanks

I know you where joking no hard fellings here , but i see you understand what i'm saying about the software right? Thank Again

See I don't mind spending the money, but if I spend the money and then the machine needs a board or something like that, than i'm going to have to spend more money. From the research that I have been doing I can rip all the guts out of this machine and replace them with different drivers like the ge...

I just tried it and the software will let me write some lines of code , but it will not let me move any of the axis on my machine. When i click on the "machine" icon it says i need to buy the full version. Is there any way to move the x,y,z without the software, i don't want to spend the money on th...

i'm going to try it now.

Thanks , but will these make the machine work, i just need to make sure the machine will move before I buy th e full version.

How new does the machine have to be? I have a 2002 Microturn, and a 2002 Micromill 2000, will it work on these machines. I have Mastercam Version 9. If not do you know where I can get a trail version of VR milling so I can see if my mill will work before I spend the money for the full version?

I would like to know if I can run a Micromill 2000 using VR Milling, and a Microlathe using VR Turning on the same computer. The computer only has one 9 pin port. Thanks

I am using a 25 pin to 25pin cable that came with this machine, the computer I have for this Microlathe only has a 25 pin comport no 9 pin ports, but my Micromill came with a 25 to 9 pin cable (haven't been able to use this one because I have no VR milling software yet) should I get a computer with ...

It shows a number 8.

I just bought a 2002 microturn with VR Turning v1.3, and installed the software on a window 98 computer, and when I click on the "machine" button the mouse pointer turns into a hour glass and doesn't let me do nothing else, I have to close the program by hitting the con,alt,del buttons on the keyboa...

Did you use mastercam to design and make the part or did you design the part in mastercam and import it in to the denford software to make it? What version mastercam did you use?

Does a Micromill 2000 need a certain cable to hook up to my computer, or can i go to any computer store and buy a cable? thanks

I just bought a Micromill 2000, and I just found a Microlathe they are both year 2002's and none have the software. If I buy the Vr software from Denford will it work on both machines. Thanks

The computer I planned on using does not have any serial ports, do you think I can use a serial to usb converter, or should I use another computer? Thanks

Do you know if there is any way to test this machine without the Vr software. I plan on buying the software from Denford, but I want to make sure the machine is fine before I spend the money, since some one cut those wires I want to make sure notting is fried before I buy it. Thanks

Thank you I just checked my machine and it is wired just like you said, but it also had wires on the AR Relay terminals 11 and 14 that went to the round plug, and wires on Terminal Block 8 pin 5, and Terminal Block 9 pin 2 that also went to the round plug. Someone cut all the wires going to the roun...