Starmill Steppers

Information and questions about Denford CNC Control electronics, general electrical issues, cables, diagrams, stepper motors, drives etc...

Moderators: Martin, Steve, Mr Magoo

Post Reply
Phil Gravett
Posts: 7
Joined: Wed 02 Apr , 2008 11:39 am
Location: Pulborough W. Sussex

Starmill Steppers

Post by Phil Gravett » Tue 04 Jan , 2011 20:56 pm

Can anybody tell me what the stepper motors are in a Starmill. I can only access the X axis one and that has no label or number that I can find. Cheers Phil.

Martin
CNC Guru
CNC Guru
Posts: 1906
Joined: Fri 24 Feb , 2006 17:09 pm
Location: Brighouse

Re: Starmill Steppers

Post by Martin » Tue 04 Jan , 2011 22:55 pm

Can you post the serial number & year of manufacture?

Phil Gravett
Posts: 7
Joined: Wed 02 Apr , 2008 11:39 am
Location: Pulborough W. Sussex

Re: Starmill Steppers

Post by Phil Gravett » Wed 05 Jan , 2011 12:07 pm

Thank you for prompt reply. As far as as I can tell, year of manufacture is probably 1993 or 1994 as I have a price list that came with it dated Jan 1993. As for serial no's, this on the main board- 98712407 Don't know where to find chassis serial, space is limited in my workshop and I have to move machine around to get at all of it. But if I know where to look.
I did find a rather worn label on the X stepper. Partially disernable- Rotalink DF?15 1/5VDCG5(or 9) is this any help? Regards Phil.

Martin
CNC Guru
CNC Guru
Posts: 1906
Joined: Fri 24 Feb , 2006 17:09 pm
Location: Brighouse

Re: Starmill Steppers

Post by Martin » Wed 05 Jan , 2011 15:40 pm

The serial plate should be on the side of the black box (electrical cabinet).

The motors are most likely,

Make Model Volts Ac/Dc Phase
x-axis MAE HY200-2220-210-BY08 30 DC
y-axis MAE HY200-2220-210-BY08 30 DC
z-axis MAE HY200-2220-210-BY08 30 DC

Phil Gravett
Posts: 7
Joined: Wed 02 Apr , 2008 11:39 am
Location: Pulborough W. Sussex

Re: Starmill Steppers

Post by Phil Gravett » Wed 05 Jan , 2011 22:53 pm

I have found the Serial number inside the white control cabinet on the bottom obscured by wires. It is 230288 Possibly preceded by a 4 so (4) 230288 probably 1993 vintage. Regards Phil.


Martin wrote:The serial plate should be on the side of the black box (electrical cabinet).

The motors are most likely,

Make Model Volts Ac/Dc Phase
x-axis MAE HY200-2220-210-BY08 30 DC
y-axis MAE HY200-2220-210-BY08 30 DC
z-axis MAE HY200-2220-210-BY08 30 DC

Martin
CNC Guru
CNC Guru
Posts: 1906
Joined: Fri 24 Feb , 2006 17:09 pm
Location: Brighouse

Re: Starmill Steppers

Post by Martin » Thu 06 Jan , 2011 10:59 am

Can you post some photos?

User avatar
Denford Admin
Site Admin
Posts: 3642
Joined: Fri 10 Feb , 2006 12:40 pm
Hardware/Software: Go to User Control Panel > Profile
Enter as much information about your CNC hardware and software as you can - it makes it easier for everyone to know what you're talking about then.
Location: Sunny Brighouse
Contact:

Re: Starmill Steppers

Post by Denford Admin » Thu 06 Jan , 2011 11:54 am

From a starmill parts list I have:
X Stepper: Cetronic Dynamics HY-200-2220-210-A8
Y Stepper: Cetronic Dynamics HY-200-2220-210-A8
Z Stepper: Cetronic Dynamics HY-200-3424-310-A8

Phil Gravett
Posts: 7
Joined: Wed 02 Apr , 2008 11:39 am
Location: Pulborough W. Sussex

Re: Starmill Steppers

Post by Phil Gravett » Thu 06 Jan , 2011 17:35 pm

Right, here is the correct information. Disregard all previous woffle. ( Should have worked for ministry of disinformation, or the government) Year of manufacture- 1988 machine serial- 280361. control serial- 230288.
Control- 24v main motor Spindle- .3hp .22KW DC Ph. Thank you again. Phil.
Attachments
starmill 001.jpg
starmill 001.jpg (734.11 KiB) Viewed 8299 times
Starmill front.jpg
Starmill front.jpg (672.97 KiB) Viewed 8299 times
Starmill front 2.jpg
Starmill front 2.jpg (665.49 KiB) Viewed 8299 times

Post Reply