Auto feeds

All info relating to Viceroy machines - Lathes, sharpedge, drills etc...

Moderators: Martin, Steve, Mr Magoo

Post Reply
Artysmarty
Posts: 28
Joined: Sun 15 Sep , 2019 14:47 pm
Hardware/Software: Denfird viceroy lathe
Location: Bolton lancs

Auto feeds

Post by Artysmarty » Fri 11 Oct , 2019 17:40 pm

DSC_1100 copy.jpg
Is this lever just for disabling the gearbox. If I change to other position then the lead screw stops turning
DSC_1100 copy.jpg (223.21 KiB) Viewed 5558 times
DSC_1105 copy.jpg
For closing the half nuts. Does this work the x feed as well as longitudinal
DSC_1105 copy.jpg (179.35 KiB) Viewed 5558 times
DSC_1104 copy.jpg
What function does this leaver have. Is it for swapping between x feed and longitudinal. The upper position doesnt seem to do any thing.
DSC_1104 copy.jpg (164.43 KiB) Viewed 5557 times
DSC_1104 copy.jpg
What function does this leaver have. Is it for swapping between x feed and longitudinal. The upper position doesnt seem to do any thing.
DSC_1104 copy.jpg (164.43 KiB) Viewed 5557 times
Attachments
DSC_1107 copy.jpg
finally. does anybody know what this is for. It was in the cabinet of my denford viceroy but is in a different color of paint than everything else.
DSC_1107 copy.jpg (185.97 KiB) Viewed 5558 times
DSC_1103 copy.jpg
ditto picture 3
DSC_1103 copy.jpg (191.19 KiB) Viewed 5558 times
DSC_1102 copy.jpg
Ths 3 position detente only seems to work the longitudinal feed via the lead screw. does it have any other function
DSC_1102 copy.jpg (175.58 KiB) Viewed 5558 times
DSC_1101 copy.jpg
Is this for reversing the screw cutting direction?
DSC_1101 copy.jpg (195.51 KiB) Viewed 5558 times

Artysmarty
Posts: 28
Joined: Sun 15 Sep , 2019 14:47 pm
Hardware/Software: Denfird viceroy lathe
Location: Bolton lancs

Re: Auto feeds

Post by Artysmarty » Fri 11 Oct , 2019 18:04 pm

Hi all forgot to say this is my viceroy TDS 1.1 Gb.
I am a newbie just feeling my way round this mc. any help would be greatly appreciated.

Regards

LesT
CNC Expert
CNC Expert
Posts: 119
Joined: Wed 11 Aug , 2010 14:17 pm
Hardware/Software: An old Viceroy with a half installed invertor drive,(when I can decide where to put the control pushbuttons I will wire it up properly)
A WMD25V mini mill.
Tractor, Bobcat 320, and Dumper truck.
7 sheds, about 5 (?) mowers. etc, etc.
Location: Scotland !

Re: Auto feeds

Post by LesT » Fri 11 Oct , 2019 21:49 pm

Hi,

Some comments on your posted pictures:

Pic 1: This is the tumbler reverse for changing the rotation direction of the leadscrew or feedscrew.
Pic 6: This lever closes the half nuts for threading. You can't do cross feed and threading at the same time. Only one shaft can be driven at a time.
Pic 5: not sure.
Pic 8: Banjo for change gears.
Pic 4: Cross feed selector.
Pic 2: Gearbox gear selector lever. (see chart for different thread selections)

There is a manual available for download here which might help you a bit:

https://cncmanual.com/viceroy-lathe/

Yours looks like an earlier version.

Regards,

Les.T.

Artysmarty
Posts: 28
Joined: Sun 15 Sep , 2019 14:47 pm
Hardware/Software: Denfird viceroy lathe
Location: Bolton lancs

Re: Auto feeds

Post by Artysmarty » Sat 12 Oct , 2019 20:00 pm

Hi Les
Thanks for your input it's much appreciate.
Art

Post Reply