TDS 1/1 Feeds and speeds plate

All info relating to Viceroy machines - Lathes, sharpedge, drills etc...

Moderators: Martin, Steve, Mr Magoo

Post Reply
dakes55
Posts: 25
Joined: Tue 24 Jan , 2017 20:50 pm
Hardware/Software: Denford Viceroy TDS 1/1 GBL

TDS 1/1 Feeds and speeds plate

Post by dakes55 » Thu 13 Apr , 2017 18:19 pm

Just wondered if anyone could send me a good picture of the speeds and feeds plate that goes below the dial, mine is missing, I might be able to make one on my laser with a good picture.
Thanks

LesT
CNC Expert
CNC Expert
Posts: 117
Joined: Wed 11 Aug , 2010 14:17 pm
Hardware/Software: An old Viceroy with a half installed invertor drive,(when I can decide where to put the control pushbuttons I will wire it up properly)
A WMD25V mini mill.
Tractor, Bobcat 320, and Dumper truck.
7 sheds, about 5 (?) mowers. etc, etc.
Location: Scotland !

Re: TDS 1/1 Feeds and speeds plate

Post by LesT » Thu 13 Apr , 2017 20:07 pm

Hi,
I think what the plate says may depend on the model of lathe,i.e. Metric or Imperial.
Mine is metric.

dakes55
Posts: 25
Joined: Tue 24 Jan , 2017 20:50 pm
Hardware/Software: Denford Viceroy TDS 1/1 GBL

Re: TDS 1/1 Feeds and speeds plate

Post by dakes55 » Thu 13 Apr , 2017 20:35 pm

Yes mine is also metric

Pete.
CNC Expert
CNC Expert
Posts: 283
Joined: Wed 07 Jan , 2009 9:46 am
Location: Kent, U.K.

Re: TDS 1/1 Feeds and speeds plate

Post by Pete. » Thu 13 Apr , 2017 21:24 pm

Is this the 12345 dial on the gearbox?

If so I might have a spare

dakes55
Posts: 25
Joined: Tue 24 Jan , 2017 20:50 pm
Hardware/Software: Denford Viceroy TDS 1/1 GBL

Re: TDS 1/1 Feeds and speeds plate

Post by dakes55 » Fri 14 Apr , 2017 8:53 am

Hi, yes the dial on mine is 1,2,3,4,5, do you want to sell it to me?
Thanks.

Pete.
CNC Expert
CNC Expert
Posts: 283
Joined: Wed 07 Jan , 2009 9:46 am
Location: Kent, U.K.

Re: TDS 1/1 Feeds and speeds plate

Post by Pete. » Fri 14 Apr , 2017 23:43 pm

Is this the thing you need?
Attachments
denfordplate.jpg
denfordplate.jpg (93.54 KiB) Viewed 9258 times

dakes55
Posts: 25
Joined: Tue 24 Jan , 2017 20:50 pm
Hardware/Software: Denford Viceroy TDS 1/1 GBL

Re: TDS 1/1 Feeds and speeds plate

Post by dakes55 » Sat 15 Apr , 2017 8:52 am

Yes thats the one i need

Pete.
CNC Expert
CNC Expert
Posts: 283
Joined: Wed 07 Jan , 2009 9:46 am
Location: Kent, U.K.

Re: TDS 1/1 Feeds and speeds plate

Post by Pete. » Sat 15 Apr , 2017 9:42 am

Ok send me a message with your address, pay the postage and it's yours.

I seriously recommend you make your best effort to change that front plate without removing the gear change lever though. It has an odd number of splines and teeth on the rack gear and if the pinion disengages it's easty to trash the gears by not getting it back in with full engagement.

Artysmarty
Posts: 28
Joined: Sun 15 Sep , 2019 14:47 pm
Hardware/Software: Denfird viceroy lathe
Location: Bolton lancs

Re: TDS 1/1 Feeds and speeds plate

Post by Artysmarty » Wed 16 Oct , 2019 13:18 pm

Hi
Long shot here but can you remove that front gearbox cover without removing the gear selector lever.

Post Reply