Milling Machine
Moderators: Martin, Steve, Mr Magoo
-
- Posts: 3
- Joined: Fri 18 May , 2007 11:57 am
- Location: Grimsby, Lincolnshire
Milling Machine
Does anyone have any information or a manual for for a Denford milling machine model No. TDS/34/VSP?
- Attachments
-
- Denford Milling Machine 001.jpg (124.01 KiB) Viewed 12191 times
-
- CNC Guru
- Posts: 396
- Joined: Mon 20 Nov , 2006 18:19 pm
- Hardware/Software: 280 VS lathe, Denford Senior E-type mill, Senior Major Universal Mill
- Location: East Midlands, UK
Mill
I believe these were badged far eastern imports, and later provided the basis for the Easimill CNC machines - see ( viewtopic.php?t=373 ).
I recall seeing some literature relating to manual mills like this when I visited Denford, but I can't remember if it was just advertising material from the far eastern manufacturers or if there was a manual.
After sorting through various boxes of information, I put a lot of stuff relating to manual machines in one pile, which (hopefully) Admin knows where. He might be able to find something there.
Andy
I recall seeing some literature relating to manual mills like this when I visited Denford, but I can't remember if it was just advertising material from the far eastern manufacturers or if there was a manual.
After sorting through various boxes of information, I put a lot of stuff relating to manual machines in one pile, which (hopefully) Admin knows where. He might be able to find something there.
Andy
-
- Posts: 3
- Joined: Fri 18 May , 2007 11:57 am
- Location: Grimsby, Lincolnshire
Denford Milling
Many thanks for the reply
Regards
Paul
Regards
Paul
- Denford Admin
- Site Admin
- Posts: 3642
- Joined: Fri 10 Feb , 2006 12:40 pm
- Hardware/Software: Go to User Control Panel > Profile
Enter as much information about your CNC hardware and software as you can - it makes it easier for everyone to know what you're talking about then. - Location: Sunny Brighouse
- Contact:
I found this manual for a VIP (V1P ?) which looks similar
The word Warco A1S has VIP written over it inside the book
There is another short manual which says
The word Warco A1S has VIP written over it inside the book
There is another short manual which says
And another set of type written sheets for the V1P and V2P Vertical Milling MachinesInstruction manual for:
M1 Horizontal Miller
Major Horizontal Miller
ELT Horizontal Miller
VS Horizontal Miller
Junior Miller
Universal Horizontal Swivel Table
Hand lever Horizontal Miller
Light Vertical Type S Miller
- Attachments
-
- vip-v1p-warco-a1s.JPG (129.64 KiB) Viewed 12155 times
-
- CNC Guru
- Posts: 396
- Joined: Mon 20 Nov , 2006 18:19 pm
- Hardware/Software: 280 VS lathe, Denford Senior E-type mill, Senior Major Universal Mill
- Location: East Midlands, UK
I was thinking that it was probably very similar to the machines that were badged by Warco, Myford, Graham Engineering (Alpine), etc.
The other manual, for M1, Major, ELT, VS etc is for Tom Senior machines - I thought I remembered seeing one for them.
I'd like a copy of that next time I'm there, as it covers both of my mills (a Tom Senior VS and a Denford Senior E-type. Then I'll then scan / reproduce it and post it in the downloads section.
Andy
The other manual, for M1, Major, ELT, VS etc is for Tom Senior machines - I thought I remembered seeing one for them.
I'd like a copy of that next time I'm there, as it covers both of my mills (a Tom Senior VS and a Denford Senior E-type. Then I'll then scan / reproduce it and post it in the downloads section.
Andy
- Denford Admin
- Site Admin
- Posts: 3642
- Joined: Fri 10 Feb , 2006 12:40 pm
- Hardware/Software: Go to User Control Panel > Profile
Enter as much information about your CNC hardware and software as you can - it makes it easier for everyone to know what you're talking about then. - Location: Sunny Brighouse
- Contact:
-
- Posts: 3
- Joined: Fri 18 May , 2007 11:57 am
- Location: Grimsby, Lincolnshire
Denford Milling Machine
Andy
Many thanks for your efforts in locating a manual for my machine, the photo diagram looks identical to the mill I have.
Kind regards
Paul
Many thanks for your efforts in locating a manual for my machine, the photo diagram looks identical to the mill I have.
Kind regards
Paul
- Denford Admin
- Site Admin
- Posts: 3642
- Joined: Fri 10 Feb , 2006 12:40 pm
- Hardware/Software: Go to User Control Panel > Profile
Enter as much information about your CNC hardware and software as you can - it makes it easier for everyone to know what you're talking about then. - Location: Sunny Brighouse
- Contact: