Tail stock issue disassembling

All info relating to Viceroy machines - Lathes, sharpedge, drills etc...

Moderators: Martin, Steve, Mr Magoo

Post Reply
Agors
Posts: 13
Joined: Mon 15 Feb , 2021 19:56 pm
Hardware/Software: Microrouter v5

Tail stock issue disassembling

Post by Agors » Sun 14 Nov , 2021 22:08 pm

Hello guys,

I’m having lots of issue disassembling the tail stick of my viceroy.

I need to do it cause the adjustment is completely off, and I need to understand how to make it work.
I think the adjustment is a lever on the side that broke a certain point in his life.

Can you please help me telling me how to disassemble it?
Do you have a graph for this version? I searched but wasn’t matching.

Mine should be the educational lathe version TD
Attachments
3737A069-8E31-4263-A4E6-28F8C3EF9A39.jpeg
3737A069-8E31-4263-A4E6-28F8C3EF9A39.jpeg (388.48 KiB) Viewed 9178 times
9F76A1FC-2FE4-4CDA-8652-3BDFC8A2BBF8.jpeg
9F76A1FC-2FE4-4CDA-8652-3BDFC8A2BBF8.jpeg (387.28 KiB) Viewed 9178 times
ED9719E8-986C-4586-88E5-7A25AF56B17A.jpeg
ED9719E8-986C-4586-88E5-7A25AF56B17A.jpeg (603.55 KiB) Viewed 9178 times
65AD76D4-1CE4-45AC-9F82-9173C6F17246.jpeg
65AD76D4-1CE4-45AC-9F82-9173C6F17246.jpeg (569.57 KiB) Viewed 9178 times
2431E939-CCC5-43E4-8685-4468E985EB64.jpeg
2431E939-CCC5-43E4-8685-4468E985EB64.jpeg (645.38 KiB) Viewed 9178 times

LesT
CNC Expert
CNC Expert
Posts: 119
Joined: Wed 11 Aug , 2010 14:17 pm
Hardware/Software: An old Viceroy with a half installed invertor drive,(when I can decide where to put the control pushbuttons I will wire it up properly)
A WMD25V mini mill.
Tractor, Bobcat 320, and Dumper truck.
7 sheds, about 5 (?) mowers. etc, etc.
Location: Scotland !

Re: Tail stock issue disassembling

Post by LesT » Wed 17 Nov , 2021 0:05 am

Hi, I just saw your post, apologies if you have solved your problem by now.
I have a copy of an Assembly drawing ML100/700 which looks pretty similar to your tailstock.
The drawing shows two clamping screws which oppose each other and can move the body from side to side when it isn't
clamped to the bed. That might be the apparently broken screw you can see in your picture next to the clamp handle.
However I don't see the opposite screw, so it may be a different model of tailstock.
Anyway, it looks like you will need to drill the screw out, or maybe try and drill a hole up the centre and try an "Easyout", I don't think this will work though because it most likely broke when being over tightened. It's shown as 5/16 Whitworth by the way.
I can scan in the drawing if you can't find it in the files section.
Les.T.

Agors
Posts: 13
Joined: Mon 15 Feb , 2021 19:56 pm
Hardware/Software: Microrouter v5

Re: Tail stock issue disassembling

Post by Agors » Wed 17 Nov , 2021 11:24 am

Thanks,

Unfortunately I have not fix it yet.

I’ll try to remove the broken bolt today (welding a nut?)

I looked in the download section but appear to be different.
If you cs. Upload a picture that would help.

I’ll post updates later

Agors
Posts: 13
Joined: Mon 15 Feb , 2021 19:56 pm
Hardware/Software: Microrouter v5

Re: Tail stock issue disassembling

Post by Agors » Wed 17 Nov , 2021 17:04 pm

Ok,
I managed to remove the broken pin, now I need to understand how the adjustment works.

Can you see any issue from the picture attached?
I guess it’s an eccentric bush that change the position.
Attachments
5847DC2C-12E6-4EF8-B0D6-0C37ABB59D54.jpeg
5847DC2C-12E6-4EF8-B0D6-0C37ABB59D54.jpeg (1.24 MiB) Viewed 9154 times
11F8E42F-9DEC-4680-A046-6416D674C5BE.jpeg
11F8E42F-9DEC-4680-A046-6416D674C5BE.jpeg (685.96 KiB) Viewed 9154 times
E25D5F3A-2802-448E-85E8-BCFA48F6FE08.jpeg
E25D5F3A-2802-448E-85E8-BCFA48F6FE08.jpeg (461.78 KiB) Viewed 9154 times

LesT
CNC Expert
CNC Expert
Posts: 119
Joined: Wed 11 Aug , 2010 14:17 pm
Hardware/Software: An old Viceroy with a half installed invertor drive,(when I can decide where to put the control pushbuttons I will wire it up properly)
A WMD25V mini mill.
Tractor, Bobcat 320, and Dumper truck.
7 sheds, about 5 (?) mowers. etc, etc.
Location: Scotland !

Re: Tail stock issue disassembling

Post by LesT » Wed 17 Nov , 2021 21:41 pm

ML100-700.jpg
ML100-700.jpg (236.76 KiB) Viewed 9147 times
ML100-700.jpg
ML100-700.jpg (236.76 KiB) Viewed 9147 times
Your tailstock is not the same as the one shown in the scanned drawing, it looks like the side ways movement is produced by screwing the bolt in and out of the keyway piece, the bolt itself can't move because it is trapped by a blocking pin.
You can either replace the broken bolt or do a modification to make the tailstock movement similar to the drawing one.
I think I would do the modification, looks to be quite simple to do.

Les.T.
Attachments
ML100-700-2.jpg
ML100-700-2.jpg (310.07 KiB) Viewed 9147 times

Agors
Posts: 13
Joined: Mon 15 Feb , 2021 19:56 pm
Hardware/Software: Microrouter v5

Re: Tail stock issue disassembling

Post by Agors » Thu 18 Nov , 2021 20:14 pm

Thanks for the scans;

In the end, I fixed the broken screw and tried, and as expected the regulation works perfectly.

So problem solved!
Thanks for the support!

Post Reply