VLS3.50

Help, advise and examples created by the Universal Laser Systems (ULS) VersaLaser laser cutting / marking machine supplied by Denford

Moderators: Martin, Steve, Mr Magoo

TracyB
Posts: 13
Joined: Thu 28 Apr , 2016 10:08 am
Hardware/Software: Universal Laser System VLS3.50
LaserCAM 2D Design

VLS3.50

Post by TracyB » Thu 28 Apr , 2016 10:37 am

Hi,
I am having a problem with our VLS3.50 in that it is connecting to the PC, it is powered up but on pressing the activate laser, it lights up initialising and nothing happens at all.....it doesn't flash green, it turns grey and static. It sometimes shows door open, even though the door is closed!
Any ideas would be gratefully received.
Tracy.

Martin
CNC Guru
CNC Guru
Posts: 1897
Joined: Fri 24 Feb , 2006 17:09 pm
Location: Brighouse

Re: VLS3.50

Post by Martin » Thu 28 Apr , 2016 11:08 am

Hi Tracy,

Check that you have 240 volt to the machine. The kettle plug to the machine may just be loose.

TracyB
Posts: 13
Joined: Thu 28 Apr , 2016 10:08 am
Hardware/Software: Universal Laser System VLS3.50
LaserCAM 2D Design

Re: VLS3.50

Post by TracyB » Thu 28 Apr , 2016 11:19 am

Red light flashing on laser control panel, door is closed, although it says door open on PC/
The power lead is plugged in correctly.
The left hand door hinge does seem particularly loose, would this affect the signals at all?
Last edited by TracyB on Thu 28 Apr , 2016 11:54 am, edited 1 time in total.

Martin
CNC Guru
CNC Guru
Posts: 1897
Joined: Fri 24 Feb , 2006 17:09 pm
Location: Brighouse

Re: VLS3.50

Post by Martin » Thu 28 Apr , 2016 11:28 am

The CPU powers up via the 5 volts from the USB lead of the computer so it is normal to see the lights & the door open message. The axis, laser cartridge & guard interlock then run from the 2 internal 48 volt DC power supply's which are powered directly from the 240 volts. You could check the 2 fuses in the kettle plug socket on the machine. It may be worth checking the voltage at the end of the kettle plug lead.

TracyB
Posts: 13
Joined: Thu 28 Apr , 2016 10:08 am
Hardware/Software: Universal Laser System VLS3.50
LaserCAM 2D Design

Re: VLS3.50

Post by TracyB » Thu 28 Apr , 2016 12:25 pm

Fuses are all OK as is the kettle lead itself.

Everything is working up to the initialising, this is when it freezes or gives the' door open' message.

Martin
CNC Guru
CNC Guru
Posts: 1897
Joined: Fri 24 Feb , 2006 17:09 pm
Location: Brighouse

Re: VLS3.50

Post by Martin » Thu 28 Apr , 2016 13:01 pm

Can you move the slides or are the drives powered up?

TracyB
Posts: 13
Joined: Thu 28 Apr , 2016 10:08 am
Hardware/Software: Universal Laser System VLS3.50
LaserCAM 2D Design

Re: VLS3.50

Post by TracyB » Thu 28 Apr , 2016 13:44 pm

The slides can move freely.

Martin
CNC Guru
CNC Guru
Posts: 1897
Joined: Fri 24 Feb , 2006 17:09 pm
Location: Brighouse

Re: VLS3.50

Post by Martin » Thu 28 Apr , 2016 14:15 pm

Can you confirm that the kettle plug has 240 volts & is fully pushed in?

TracyB
Posts: 13
Joined: Thu 28 Apr , 2016 10:08 am
Hardware/Software: Universal Laser System VLS3.50
LaserCAM 2D Design

Re: VLS3.50

Post by TracyB » Thu 28 Apr , 2016 14:39 pm

Kettle plug has 240v and is fully pushed in.
The left hand lid hinge is very ropey.....would this affect the functioning?

Martin
CNC Guru
CNC Guru
Posts: 1897
Joined: Fri 24 Feb , 2006 17:09 pm
Location: Brighouse

Re: VLS3.50

Post by Martin » Thu 28 Apr , 2016 15:10 pm

No I would`t think so.

Have you checked the 2 fuses in the kettle plug socket?

TracyB
Posts: 13
Joined: Thu 28 Apr , 2016 10:08 am
Hardware/Software: Universal Laser System VLS3.50
LaserCAM 2D Design

Re: VLS3.50

Post by TracyB » Fri 29 Apr , 2016 7:33 am

All fuses OK, battery new, USB cable new, Voltage checked and OK, machine all cleaned and vacuumed, software up-to-date, tried on a variety of computers......all hunky-dory up to the point of initialising, then nothing.........or door open message.......very bizarre!!!!

Martin
CNC Guru
CNC Guru
Posts: 1897
Joined: Fri 24 Feb , 2006 17:09 pm
Location: Brighouse

Re: VLS3.50

Post by Martin » Fri 29 Apr , 2016 10:51 am

Can you try the latest version of software please? http://www.denfordata.com/downloads/Uni ... .57.46.zip

I know when you first had the machine there was a issue with it running using a USB 3 Port.

TracyB
Posts: 13
Joined: Thu 28 Apr , 2016 10:08 am
Hardware/Software: Universal Laser System VLS3.50
LaserCAM 2D Design

Re: VLS3.50

Post by TracyB » Fri 29 Apr , 2016 11:11 am

I am in the process of getting IT support to check.

TracyB
Posts: 13
Joined: Thu 28 Apr , 2016 10:08 am
Hardware/Software: Universal Laser System VLS3.50
LaserCAM 2D Design

Re: VLS3.50

Post by TracyB » Fri 29 Apr , 2016 12:00 pm

There is now an error message #38 showing on screen.

TracyB
Posts: 13
Joined: Thu 28 Apr , 2016 10:08 am
Hardware/Software: Universal Laser System VLS3.50
LaserCAM 2D Design

Re: VLS3.50

Post by TracyB » Fri 29 Apr , 2016 12:03 pm

Also, bottom right hand corner of screen.......'service required (code 1003)!!!!

Martin
CNC Guru
CNC Guru
Posts: 1897
Joined: Fri 24 Feb , 2006 17:09 pm
Location: Brighouse

Re: VLS3.50

Post by Martin » Fri 29 Apr , 2016 14:11 pm

Can you unplug the USB wire & try it again.

TracyB
Posts: 13
Joined: Thu 28 Apr , 2016 10:08 am
Hardware/Software: Universal Laser System VLS3.50
LaserCAM 2D Design

Re: VLS3.50

Post by TracyB » Fri 29 Apr , 2016 14:26 pm

The USB cable is new and has been unplugged and plugged back in, it seems as if the signal gets lost from activating the engraver.

Martin
CNC Guru
CNC Guru
Posts: 1897
Joined: Fri 24 Feb , 2006 17:09 pm
Location: Brighouse

Re: VLS3.50

Post by Martin » Fri 29 Apr , 2016 14:34 pm

Can you get the IT to unplug the USB cable & remove the ULS software then re install it & connect the USB cable.

TracyB
Posts: 13
Joined: Thu 28 Apr , 2016 10:08 am
Hardware/Software: Universal Laser System VLS3.50
LaserCAM 2D Design

Re: VLS3.50

Post by TracyB » Tue 03 May , 2016 9:52 am

IT has uninstalled and reinstalled. It seems the laser itself is dead, it is not physically moving and making no noise at all......which it does when it is initialising!!!!

TracyB
Posts: 13
Joined: Thu 28 Apr , 2016 10:08 am
Hardware/Software: Universal Laser System VLS3.50
LaserCAM 2D Design

Re: VLS3.50

Post by TracyB » Tue 03 May , 2016 10:22 am

Can you offer any service contract Martin? If so, what are the costs involved???

Post Reply