Novamill Spindle

All info relating to the Denford Novamill CNC Milling machines

Moderators: Martin, Steve, Mr Magoo

Post Reply
akkord64
Posts: 2
Joined: Tue 26 Aug , 2014 12:24 pm
Hardware/Software: Novamill - Was parted out before I purchased it. Need to aquire spindle and head, else I will build.

Novamill Spindle

Post by akkord64 » Fri 12 Sep , 2014 13:34 pm

Hello all. I am hoping the admin or a kind member can help me out. I purchased a Novamill that was striped of its ATC spindle assembly. I am OK with having one made locally and have the RM6-100 diagram which gives a nice overview. Is there anyone who has dimensioned drawings or is kind enough to measure and photo a spindle assembly with the appropriate measurements to re-create this unit? I have sent requests into Denford via email for information, but I have not received a reply from them. I fear they either don't know, or are not willing to assist. Thanks!

goodstuff
Posts: 1
Joined: Sat 04 Oct , 2014 13:41 pm

Re: Novamill Spindle

Post by goodstuff » Sat 04 Oct , 2014 13:46 pm

Did you have any luck with this ?
Last edited by goodstuff on Sun 28 Jun , 2020 10:15 am, edited 1 time in total.

DavidJ
Posts: 16
Joined: Mon 19 Aug , 2013 7:34 am
Hardware/Software: Novamill
Location: Teesside

Re: Novamill Spindle

Post by DavidJ » Mon 08 Dec , 2014 13:43 pm

Can anyone clarify for me if the disc springs shown in drawing RM6/100 have a spacer between the upper and lower stacks, or if there is actually a single stack with rather more than the 14 springs shown?

Martin
CNC Guru
CNC Guru
Posts: 1897
Joined: Fri 24 Feb , 2006 17:09 pm
Location: Brighouse

Re: Novamill Spindle

Post by Martin » Mon 08 Dec , 2014 14:03 pm

No spacers & 27 Disc Springs according to the parts list.

DavidJ
Posts: 16
Joined: Mon 19 Aug , 2013 7:34 am
Hardware/Software: Novamill
Location: Teesside

Re: Novamill Spindle

Post by DavidJ » Mon 08 Dec , 2014 14:23 pm

Thanks Martin.

DavidJ
Posts: 16
Joined: Mon 19 Aug , 2013 7:34 am
Hardware/Software: Novamill
Location: Teesside

Re: Novamill Spindle

Post by DavidJ » Sun 11 Jan , 2015 17:38 pm

Is the parts list available? The assembly drawings are of limited use without parts list?

What about part drawings - or is the ATC (or parts of it) used in a current/recent model ?

Martin
CNC Guru
CNC Guru
Posts: 1897
Joined: Fri 24 Feb , 2006 17:09 pm
Location: Brighouse

Re: Novamill Spindle

Post by Martin » Sun 11 Jan , 2015 21:13 pm

I will try to post them on Monday

Martin
CNC Guru
CNC Guru
Posts: 1897
Joined: Fri 24 Feb , 2006 17:09 pm
Location: Brighouse

Re: Novamill Spindle

Post by Martin » Mon 12 Jan , 2015 13:13 pm

Hope this helps
Attachments
DOC120115.pdf
(484.46 KiB) Downloaded 1445 times

DavidJ
Posts: 16
Joined: Mon 19 Aug , 2013 7:34 am
Hardware/Software: Novamill
Location: Teesside

Re: Novamill Spindle

Post by DavidJ » Tue 13 Jan , 2015 15:11 pm

Thanks - that is very helpful.

Are similar parts lists available for drawings RM6_700 & RM6_700C ? (the ATC carousel).

Martin
CNC Guru
CNC Guru
Posts: 1897
Joined: Fri 24 Feb , 2006 17:09 pm
Location: Brighouse

Re: Novamill Spindle

Post by Martin » Tue 13 Jan , 2015 18:06 pm

I will have a look but not in the factory until the end of the week.

Post Reply