Micromill 2000 Denstep LED stuck on flasing dot L ??

All info relating to the Denford MicroMill and MicroTurn lathes and mills

Moderators: Martin, Steve, Mr Magoo

Post Reply
JSKRABA
CNC Apprentice
CNC Apprentice
Posts: 50
Joined: Sat 11 Nov , 2006 19:17 pm

Micromill 2000 Denstep LED stuck on flasing dot L ??

Post by JSKRABA » Mon 06 Jan , 2014 22:50 pm

Hi
Micromill 2000 with denstep (2001) when switching on, board sets and LED stays with .L (flashing dot)
I think it should go to 8 (all Leds on) to show its ready to connect.
With the .L it can not make a serial connection.
Any Ideas On What this could be? Anyone!

Ta

Martin
CNC Guru
CNC Guru
Posts: 1897
Joined: Fri 24 Feb , 2006 17:09 pm
Location: Brighouse

Re: Micromill 2000 Denstep LED stuck on flasing dot L ??

Post by Martin » Tue 07 Jan , 2014 6:56 am

It sounds like the mint file is not running. What software are you using to connect? If it's VRMilling make sure you are using the latest version.

JSKRABA
CNC Apprentice
CNC Apprentice
Posts: 50
Joined: Sat 11 Nov , 2006 19:17 pm

Re: Micromill 2000 Denstep LED stuck on flasing dot L ??

Post by JSKRABA » Tue 07 Jan , 2014 17:52 pm

Hi
Running from VrmillingV2.3 and V5x both the same problem
The card has a ROM V2.0b10/s/b19-JD5 should this be OK or does it need V2.1 ROM?
I thought this Rom would be OK with V2.3.
Pic attached

Ta
Attachments
P1000955.jpg
P1000955.jpg (130.42 KiB) Viewed 6821 times

Martin
CNC Guru
CNC Guru
Posts: 1897
Joined: Fri 24 Feb , 2006 17:09 pm
Location: Brighouse

Re: Micromill 2000 Denstep LED stuck on flasing dot L ??

Post by Martin » Tue 07 Jan , 2014 18:45 pm

It should be a version 2.1 Eprom.

The latest version of VRMilling 2 is version 2.31 & can be downloaded from the Denford website. Make sure you have a copy of the licence file first though.

If you have VRMilling 5 then make sure you select a legacy machine.

You can also try to download the mint program using mintman which should be installed in the VRMilling directory.

JSKRABA
CNC Apprentice
CNC Apprentice
Posts: 50
Joined: Sat 11 Nov , 2006 19:17 pm

Re: Micromill 2000 Denstep LED stuck on flasing dot L ??

Post by JSKRABA » Wed 08 Jan , 2014 16:12 pm

Hi
All sorted now, I had tried two cables that work fine on Router and Novamill but NOT on this Micromill
after some swapping and fiddling with cables got one that works ok.
How many different ways can you connect a 9pin-25pin from the card to the output panel!!

Ta for your time.

Martin
CNC Guru
CNC Guru
Posts: 1897
Joined: Fri 24 Feb , 2006 17:09 pm
Location: Brighouse

Re: Micromill 2000 Denstep LED stuck on flasing dot L ??

Post by Martin » Wed 08 Jan , 2014 18:31 pm

Yes. 2 ways.

The Micromill & Microturn use a pin to pin cable cable. The others all use a RS232 lead. The difference is pins 2 & 3 are crossed over.

Post Reply