Viceroy TDS/1 Lathe

If you've had enough of reading, then look at these pictures of the "good" old days. Machine brochures, magazines etc..

Moderators: Martin, Steve, Mr Magoo

Post Reply
samson
Posts: 2
Joined: Fri 25 Jul , 2008 23:13 pm

Viceroy TDS/1 Lathe

Post by samson » Fri 25 Jul , 2008 23:35 pm

I have just acquired a Viceroy TDS/1 lathe dated 1966 which has been in storage since the early 80's. It has been stored well as my friends dad was an engineering lecturer and had the foresight to cover it with grease but of course I have got this lathe from his garage and he had dismantled it to store it.

I am in the process of restoring it and would desparately like any manuals, photos, drawings, photocopies, originals, sketches on the back of cigarette packets (will pay postage etc of course) absolutely anything to help me get it back together.

User avatar
Steve
CNC Guru
CNC Guru
Posts: 1432
Joined: Tue 21 Feb , 2006 16:15 pm
Location: Denford UK

http://www.denfordata.com/bb/viewtopic.php?t=359&highlig

Post by Steve » Mon 28 Jul , 2008 15:42 pm

Hi

Welcome to the Forum :!:

You should find everything you need here.

Visit the link below for the manual.

viewtopic.php?t=359&highlight=viceroy+tds

Go to the search menu at the top of the screen and type in Viceroy TDS and I am sure you will find more than you need.

Good luck!

Keep us informed how you get on.

samson
Posts: 2
Joined: Fri 25 Jul , 2008 23:13 pm

TDS 1 Lathe

Post by samson » Wed 30 Jul , 2008 9:24 am

Hi Steve, thanks for the quick reply.

I have looked at the link you sent and downloaded it but the picture on the 1st page looks nothing like the lathe I have.

In the forum there are some pictures of the same type of lathe I have, I think they're entitled a distressed lathe or somthing like that, are there any specific serial no's etc on the lathe that I could send you to make a more specific search on this machine.

Regards Phil.

Andy B
CNC Guru
CNC Guru
Posts: 396
Joined: Mon 20 Nov , 2006 18:19 pm
Hardware/Software: 280 VS lathe, Denford Senior E-type mill, Senior Major Universal Mill
Location: East Midlands, UK

Post by Andy B » Wed 30 Jul , 2008 10:46 am

Hi Phil,

Edited to add - Does your lathe look more like the pictures later on in the manual, i.e. with a bevelled headstock casting instead of a big square-edged casting? I think the purple-coloured advertising material is from a much later date (late 1970's/early 80's) than your machine.

Serial numbers aren't much help for the manual lathes, as no-one has yet managed to find any register that identifies them to model numbers (as far as I'm aware).
To make life more difficult, there were numerous design changes done over the life of these machines whilst the same model designation was continued.
Most useful would be if you can post a picture or 2 or your 'bits', to aid initial identification. Then as you get to each major asssembly (headstock, tailstock, saddle, etc.) post a few more pictures with any specific questions.
The mechanical design of the manual lathes did not vary that much from the earliest 5" models to the later 5 1/2" ones. So I'm sure that between us we can help you to get it re-built and producing swarf once again!

Andy
Last edited by Andy B on Wed 30 Jul , 2008 11:42 am, edited 1 time in total.

Andy B
CNC Guru
CNC Guru
Posts: 396
Joined: Mon 20 Nov , 2006 18:19 pm
Hardware/Software: 280 VS lathe, Denford Senior E-type mill, Senior Major Universal Mill
Location: East Midlands, UK

Post by Andy B » Wed 30 Jul , 2008 10:52 am

Admin - can you move this one to the user stories / Projects area too?
It will complement the other TDS1 thread you just moved.

Andy

Post Reply