Search found 1434 matches
- Tue 04 Oct , 2022 11:04 am
- Forum: Triac
- Topic: spindle bearing coming loose
- Replies: 5
- Views: 8086
Re: spindle bearing coming loose
Is this the tool becoming loose in the spindle taper? There should only be 44 washers in the spring stack and these are secured by the lock nut at the top of the spindle. See the post attached as the spindle arangement should be the same as the 1300. The locknut is secured with a grub screw so shoul...
- Fri 23 Sep , 2022 9:53 am
- Forum: Electronics
- Topic: Novamill stepper driver issue
- Replies: 1
- Views: 5539
Re: Novamill stepper driver issue
I would try switching the drive to the motos by plgging the Y into the X and the X into the Y on the control card. You may have to remove the black key pins from the connector to do this. https://www.denfordata.com/bb/viewtopic.php?f=54&t=1627. Then by pressing the Y jog the X will move using the Y ...
- Wed 07 Sep , 2022 14:40 pm
- Forum: Compact 1000
- Topic: Error connecting to Router
- Replies: 2
- Views: 9203
Re: Error connecting to Router
The 18V is rectified to produce the 24V DC logic which powers on the controller and the Light.
- Thu 01 Sep , 2022 16:03 pm
- Forum: Electronics
- Topic: Novamill RPM not changing
- Replies: 3
- Views: 6550
Re: Novamill RPM not changing
The sprint drive will have a 0V 10V and analog in terminal. If you connected a pot to this you would then be able to control the speed from the pot proving thet the drive is working. Take care as the Sprint is not isolated but the analog out of the nextmove is iscolated and should change between 0-1...
- Thu 01 Sep , 2022 15:44 pm
- Forum: Router 2600
- Topic: Tee slot dimensions
- Replies: 1
- Views: 4948
Re: Tee slot dimensions
YES
Travel is 400mm in Y and slots are 40mm apart.
Travel is 400mm in Y and slots are 40mm apart.
- Thu 01 Sep , 2022 15:42 pm
- Forum: Electronics
- Topic: Novamill Sprint spindle drive 12v+ source
- Replies: 1
- Views: 5366
Re: Novamill Sprint spindle drive 12v+ source
The sprint drive may be unisolated so you must be carfull connecting it to the supply. The 0-10V from the BAldor control card is iscolated
- Thu 01 Sep , 2022 15:38 pm
- Forum: Cyclone
- Topic: AC2/106 Spacer Drawing
- Replies: 3
- Views: 6225
Re: AC2/106 Spacer Drawing
please find attached drawings. The parts are no longer in stock.
- Wed 10 Aug , 2022 8:34 am
- Forum: F1 / 4x4 / GT Racing In Schools
- Topic: Technical Data Sheet F1 Model Block
- Replies: 2
- Views: 10916
Re: Technical Data Sheet F1 Model Block
All the data we have is shown on the data sheet. Unfortunatley this is all we have.
- Fri 22 Jul , 2022 11:44 am
- Forum: Viceroy
- Topic: Viceroy Sharpedge oil?
- Replies: 2
- Views: 5335
- Tue 19 Jul , 2022 9:40 am
- Forum: Micromill / Microturn
- Topic: (HELP NEEDED) MICROTURN/QUICK TURN 2
- Replies: 1
- Views: 5138
Re: (HELP NEEDED) MICROTURN/QUICK TURN 2
Hi The simulation always shows the cutting from the top so the tool library should not be edited
In Quick Tern 2D Design make sure you have the correct tool Library selected which will also create a program cutting from the front.
In Quick Tern 2D Design make sure you have the correct tool Library selected which will also create a program cutting from the front.
- Tue 31 May , 2022 12:51 pm
- Forum: Cyclone
- Topic: Tu150P, Fanuc OT-C, doesn't bootup - no data on the screen
- Replies: 10
- Views: 9231
Re: Tu150P, Fanuc OT-C, doesn't bootup - no data on the screen
Thanks for posting the solution.
- Tue 31 May , 2022 12:50 pm
- Forum: Electronics
- Topic: CPLD needs to be updating.
- Replies: 1
- Views: 5593
Re: CPLD needs to be updating.
Hi, Is the machine functioning correctly if so I would leave the firmware as it is. What model of machine do you have and what is the date of manufacture?
- Fri 06 May , 2022 9:04 am
- Forum: VMC 1300
- Topic: VMC 1300, adjustment procedure to eliminate play in toolholder collet/spindle/drawbar assembly
- Replies: 6
- Views: 5891
Re: VMC 1300, adjustment procedure to eliminate play in toolholder collet/spindle/drawbar assembly
The tool should be pulled up tight in the taper of the spindle so there should be no movement once fitted. Could you remove a pull stud from a toolholder and check it fits in the taper correctly? All that could cause a tool fitted with the correct pull stud to be loose would be that the springs are ...
- Sat 05 Mar , 2022 19:51 pm
- Forum: VersaLaser
- Topic: How to replace mirrors 2 and 3 on versalaser
- Replies: 8
- Views: 19908
Re: How to replace mirrors 2 and 3 on versalaser
You would probably be able to see damage on the mirrors and Len’s if there is any.
A service on the laser may be worth doing. We could measure the laser power before the optics and through them.
The worst case would be you need a laser recharge but it would be worth doing.
A service on the laser may be worth doing. We could measure the laser power before the optics and through them.
The worst case would be you need a laser recharge but it would be worth doing.
- Mon 21 Feb , 2022 14:50 pm
- Forum: Turn270
- Topic: G91 on Turn 270 PRO
- Replies: 1
- Views: 5108
Re: G91 on Turn 270 PRO
Unfortunatly G91 is not supported in VR Turning.
The supported codes are listed in the help.
The supported codes are listed in the help.
- Mon 21 Feb , 2022 14:33 pm
- Forum: Novamill
- Topic: Nova Mill mint version message
- Replies: 9
- Views: 11113
Re: Nova Mill mint version message
Thats great. Thanks for letting us know.
- Tue 15 Feb , 2022 9:53 am
- Forum: Post Processors
- Topic: Fusion 360 Post Processor
- Replies: 0
- Views: 8638
Fusion 360 Post Processor
The attached post processor for Fusion 360 was supplied by Simon Edwards of Ron Dearing UTC.
- Thu 10 Feb , 2022 17:38 pm
- Forum: Denford Classifieds
- Topic: (SOLD) Deublin ltd pneumatic chuck for Mirac PC
- Replies: 12
- Views: 14431
Re: FOR SALE: Deublin ltd pneumatic chuck for Mirac PC
The chuck jaws are soft jaws designed to be machined to hold a specific bar size. You could still buy soft jaws for them.
- Thu 10 Feb , 2022 17:34 pm
- Forum: Novamill
- Topic: Nova Mill mint version message
- Replies: 9
- Views: 11113
Re: Nova Mill mint version message
hi give us a call when you are thinking of coming over. Ask for Martin or Steve.
- Thu 10 Feb , 2022 17:31 pm
- Forum: Project Of The Week
- Topic: Work Area
- Replies: 6
- Views: 9939
Re: Work Area
Hi Trevor, This post would have been better in the microrouter section on the forum https://www.denfordata.com/bb/viewforum.php?f=38 You could download the manual from there. It is possible to lower the motor mounting plate so the tools can get down to the bed. You can see the screws to adjust this ...