Search found 31 matches
- Mon 03 Jul , 2017 16:26 pm
- Forum: Triac
- Topic: Decel at end of each line of code
- Replies: 4
- Views: 4578
Re: Decel at end of each line of code
Thanks that is a good idea. Just looked at the version I am running and it is 2.14... So a little out of date. I will give it a shot!
- Sat 01 Jul , 2017 22:36 pm
- Forum: Triac
- Topic: Decel at end of each line of code
- Replies: 4
- Views: 4578
Re: Decel at end of each line of code
OK I figured it out. For those who may find this later there is a "turbo" mode that needs to be enabled in the auto run. Why it is not enabled from the beginning I don't know.
- Sat 01 Jul , 2017 19:57 pm
- Forum: Triac
- Topic: Decel at end of each line of code
- Replies: 4
- Views: 4578
Re: Decel at end of each line of code
So doing a little more reading it sounds like data starvation. I am going to check the baud rate settings... Does anybody have the recommended settings for VR milling 2? Baud rate, stop bits, polling delay? Any other suggestions? I will also try a new cable though I wouldn't think it would be the pr...
- Sat 01 Jul , 2017 16:43 pm
- Forum: Triac
- Topic: Decel at end of each line of code
- Replies: 4
- Views: 4578
Decel at end of each line of code
Hi all, I am just running my first program on my new triac using VR milling 2. My problem is the machine decelerates after each line of code and comes to a stop... Then accels to the next line resulting in a jerky motion. Is there a setting I am missing in VR milling 2 to set this to constant veloci...
- Thu 25 May , 2017 22:02 pm
- Forum: Triac
- Topic: Triac feed rate setting in VR milling 2
- Replies: 5
- Views: 5038
Re: Triac feed rate setting in VR milling 2
Might as well post a pic of the new machine
- Thu 25 May , 2017 16:26 pm
- Forum: Triac
- Topic: Triac feed rate setting in VR milling 2
- Replies: 5
- Views: 5038
Re: Triac feed rate setting in VR milling 2
1500 mm/min for x and y, 1000 mm/min for z? If it is set to high the concern is it losing steps when under load?
- Thu 25 May , 2017 12:31 pm
- Forum: Triac
- Topic: Triac feed rate setting in VR milling 2
- Replies: 5
- Views: 5038
Re: Triac feed rate setting in VR milling 2
It is a 1995 triac PC with the serial number EO4595.
- Thu 25 May , 2017 0:36 am
- Forum: Triac
- Topic: Triac feed rate setting in VR milling 2
- Replies: 5
- Views: 5038
Triac feed rate setting in VR milling 2
Hi all, I just acquired a triac with VR milling 2. When I go to jog the machine it maxes out at 39 in/min. The manual says 2500mm/min or roughly 100in/min. I went in and modified the machine feed rate parameters to match the values in the manual. Is this OK? Why was it not like this originally? Seem...
- Mon 04 Jan , 2016 1:17 am
- Forum: Software
- Topic: DOS CNC program bigger than 64 KB
- Replies: 2
- Views: 7177
Re: DOS CNC program bigger than 64 KB
I know this is an old post, but is it possible to edit the g-code in fanucsmd if it is larger than 64kb? I have figured out how to run a large file, but not edit it.
- Sun 03 Jan , 2016 3:10 am
- Forum: Micromill / Microturn
- Topic: MicroMill FANUCSMD Error - Controller Communications
- Replies: 1
- Views: 4535
Re: MicroMill FANUCSMD Error - Controller Communications
For those who stumble upon this in the future, this issue was fixed by downgrading the operating system to dos 7.1. I was unable to get the program to run in a dos emulator.
- Wed 30 Dec , 2015 0:43 am
- Forum: Micromill / Microturn
- Topic: MicroMill FANUCSMD Error - Controller Communications
- Replies: 1
- Views: 4535
MicroMill FANUCSMD Error - Controller Communications
Hi all, I need some help. I recently acquired an older micromill [Smartstep Mint 3.28 V1.6h/S-JD5] and I have been successful up to this point. So far I have installed the software and connected to the machine. My problem lies when I go to home the machine I get a Error - Controller Communications. ...