Search found 91 matches
- Mon 06 Apr , 2020 17:18 pm
- Forum: NovaTurn
- Topic: Novaturn ATC blowing fuse on startup
- Replies: 14
- Views: 13303
Re: Novaturn ATC blowing fuse on startup
well unfortunately I have had no luck with this, so i have ordered some slow burn fuses, in hopes that it will delay burning just long enough for the current spike to not toast another 12$ worth of fuses. The fuses i have been replacing it with are the same rating as the one that I have used for a l...
- Sun 05 Apr , 2020 2:10 am
- Forum: NovaTurn
- Topic: Novaturn ATC blowing fuse on startup
- Replies: 14
- Views: 13303
Re: Novaturn ATC blowing fuse on startup
Motor runs fine when disconnected from the turret, and no fuse burns, but as soon as it stalls in the turret it burns the fuse. Why would it be consuming more power to stall?
- Sun 05 Apr , 2020 1:40 am
- Forum: NovaTurn
- Topic: Novaturn ATC blowing fuse on startup
- Replies: 14
- Views: 13303
Novaturn ATC blowing fuse on startup
Hey guys, so my atc control board has started blowing fuses as soon as power gets to it. Not sure what could even cause this, as the motor is always "stalled" right? I am tempted to place a higher burn fuse, but don't want to burn anything sensitive. I have recently readjusted the tool center, and h...
- Fri 03 Apr , 2020 19:25 pm
- Forum: Denford Classifieds
- Topic: (SOLD) Deublin ltd pneumatic chuck for Mirac PC
- Replies: 12
- Views: 13860
Re: FOR SALE: Deublin ltd pneumatic chuck for Mirac PC
OOF lol! Well i guess my last question would be about your price! do you have a rough idea what you hope to get out of it?
- Fri 03 Apr , 2020 17:06 pm
- Forum: Denford Classifieds
- Topic: (SOLD) Deublin ltd pneumatic chuck for Mirac PC
- Replies: 12
- Views: 13860
Re: FOR SALE: Deublin ltd pneumatic chuck for Mirac PC
What is the diameter of the rotary union behind the chuck? I would like to know if I can pass that through my spindle. That bump is definitely concerning. if you have an opportunity to mount an indicator on the chuck body and tip on the jaw, how much can you wiggle it? I am in the US in Wisconsin, w...
- Fri 03 Apr , 2020 1:58 am
- Forum: Micromill / Microturn
- Topic: Adding a 4th axis to micromill
- Replies: 14
- Views: 15658
Re: Adding a 4th axis to micromill
I STILL HAVEN'T DONE MUCH MORE THAN A FEW SMALL CUTS!!! I have been in the process of moving all my projects to my shop, and have not had much time to program some fun stuff yet. I have had a little time here and there to finish mounting my mist cooling, dial in the steps per degree of the rotary ta...
- Fri 03 Apr , 2020 1:45 am
- Forum: Denford Classifieds
- Topic: (SOLD) Deublin ltd pneumatic chuck for Mirac PC
- Replies: 12
- Views: 13860
Re: FOR SALE: Deublin ltd pneumatic chuck for Mirac PC
Very cool! I really have no idea how to price a chuck let alone sight unseen lol, do you have an idea what price you would be happy with? You mentioned it has been bumped, so I'm not super confident I would want to pay an arm! Could you post pics?
- Wed 01 Apr , 2020 21:29 pm
- Forum: Denford Classifieds
- Topic: (SOLD) Deublin ltd pneumatic chuck for Mirac PC
- Replies: 12
- Views: 13860
Re: FOR SALE: Deublin ltd pneumatic chuck for Mirac PC
Open to offers?
- Wed 01 Apr , 2020 21:22 pm
- Forum: VR Milling - All Versions
- Topic: VR 5 vs spindle Probe
- Replies: 1
- Views: 8795
Re: VR 5 vs spindle Probe
Dug up an old post, but i'm interested. I would like to be able to automatically probe tool heights after a tool change. Has this been attempted by denford?
- Wed 18 Dec , 2019 7:11 am
- Forum: NovaTurn
- Topic: Novaturn Software
- Replies: 11
- Views: 13052
Re: Novaturn Software
Hi Nick, Can you post pictures of your control board? It seems like a lot of machines have the updated eeprom, so perhaps yours was updated at some point. As far as connecting your machine to a Windows computer, I have had mixed luck with a serial card, but have had great luck with a USB to db9 cabl...
- Tue 26 Nov , 2019 16:27 pm
- Forum: Electronics
- Topic: Digiplan sd3 replacements
- Replies: 1
- Views: 3163
Re: Digiplan sd3 replacements
If you are on Mach 3, you must have a break out board between the drivers and your computer. Find out what that outputs, as well as what power requirements the motors have. You may need to make a large power supply for delivering a lot of clean DC to your steppers (well to your drivers to give to st...
- Mon 25 Nov , 2019 23:54 pm
- Forum: Denford Classifieds
- Topic: Denford Triac for sale
- Replies: 1
- Views: 3707
Re: Denford Triac for sale
where?
- Mon 25 Nov , 2019 23:44 pm
- Forum: Software
- Topic: Old Machines, Old Software, Dongles and Floppy Disks, Help!
- Replies: 9
- Views: 13451
Re: Old Machines, Old Software, Dongles and Floppy Disks, Help!
Were you able to get this sorted? I had previously documented my attempts to get vr turning to run on win 10, but have not had much time to push it forward. The concept is the same for VR milling, and if you are at a loss, perhaps reading this will be of some help: http://www.denfordata.com/bb/viewt...
- Tue 15 Oct , 2019 14:34 pm
- Forum: NovaTurn
- Topic: Air chuck for novaturn
- Replies: 4
- Views: 8844
Re: Air chuck for novaturn
Hi Steve,
Do you happen to have any pictures or diagrams of the air chuck? Was this machined by denford, or was it a sourced chuck?
Do you happen to have any pictures or diagrams of the air chuck? Was this machined by denford, or was it a sourced chuck?
- Thu 03 Oct , 2019 15:14 pm
- Forum: Electronics
- Topic: USB to RS232 adapter
- Replies: 2
- Views: 13974
Re: USB to RS232 adapter
well I don't know if you are still checking this, or if you ever got an answer, but this adapter has been working for me with windows 10 and vr milling 5 as well as Vr Turning: https://www.amazon.com/gp/product/B01DYNNUS8/ref=ppx_yo_dt_b_asin_title_o02_s00?ie=UTF8&psc=1 if that link doesnt work in t...
- Wed 02 Oct , 2019 14:33 pm
- Forum: NovaTurn
- Topic: Air chuck for novaturn
- Replies: 4
- Views: 8844
Re: Air chuck for novaturn
Guess I'm probably going to make a pneumatic collet closer instead! This may be a stupid question, but is the spindle face a standard size? I don't have it in front of me to measure the hole spacing and such, but it seems like there aught to be a collet holder that fits the face.
- Tue 01 Oct , 2019 23:03 pm
- Forum: Micromill / Microturn
- Topic: Adding a 4th axis to micromill
- Replies: 14
- Views: 15658
Re: Adding a 4th axis to micromill
More power did the trick! I used a laptop power supply, giving 19.5v at 4 amp. Much more than required, but within the range that both the motor and the controller could function. Wiring in the new supply was easy, I ended up just running it in parallel with the ac transformer, as this is controlled...
- Sat 28 Sep , 2019 7:29 am
- Forum: Micromill / Microturn
- Topic: Adding a 4th axis to micromill
- Replies: 14
- Views: 15658
Re: Adding a 4th axis to micromill
We have motion!! Tonight I got it all wired up and turning! It seems to struggle with torque, so I am starting to regret wiring my stepper in bipolar series (lower power consumption and torque) I plan to try hooking in a new power supply for that drive, as I would like to make sure it is maxed out o...
- Thu 26 Sep , 2019 18:10 pm
- Forum: Micromill / Microturn
- Topic: Adding a 4th axis to micromill
- Replies: 14
- Views: 15658
Re: Adding a 4th axis to micromill
Well I always seem to think things will just fall into place. Here is another minor detail I need to sort. my stepper driver is for a 4 wire bipolar motor. I have an 8 wire stepper, wired into 5 wires with a ground for a total of 6 wires in the cable. This is a cool opportunity to learn about bipola...
- Thu 26 Sep , 2019 17:59 pm
- Forum: Electronics
- Topic: Corrosion and rs232 performance
- Replies: 4
- Views: 5017
Re: Corrosion and rs232 performance
I'm not sure I said anything you probably didn't already know, but hopefully you can get it cleaned up. That reminds me that I need to either remove my batteries or spray a coating around it for when this inevitably happens to mine! Let us know if you can get it back to functional