Search found 74 matches

by jamesgates1000
Thu 15 Oct , 2015 9:49 am
Forum: Cyclone
Topic: Cyclone with 300 and 438 alarms
Replies: 14
Views: 6118

Re: Cyclone with 300 and 438 alarms

Hi, did you manage to find those parameters?
by jamesgates1000
Sun 11 Oct , 2015 19:31 pm
Forum: Cyclone
Topic: Cyclone with 300 and 438 alarms
Replies: 14
Views: 6118

Re: Cyclone with 300 and 438 alarms

Hi, I got the cyclone and a triac from an auctioneers, they were selling them on behalf of Gateshead college. There is Gateshead college stickers on both of them.
Thanks
by jamesgates1000
Sat 10 Oct , 2015 21:05 pm
Forum: Cyclone
Topic: Cyclone with 300 and 438 alarms
Replies: 14
Views: 6118

Re: Cyclone with 300 and 438 alarms

Someone at work suggested that it might be that the axis had seized. I took off the side panel and moved the x axis to the centre of its travel. Seemed a little stiff at first but not too bad. Now the 401 and 438 alarms have gone, and i am getting a 441 alarm - n AXIS : ABNORMAL CURRENT OFFSET Any i...
by jamesgates1000
Sat 10 Oct , 2015 21:00 pm
Forum: Triac
Topic: Fanuc Triac Overtravel Alarm
Replies: 4
Views: 1735

Re: Fanuc Triac Overtravel Alarm

Axis override switch didnt work,

I took the back cover off...
Back Panel.jpg
Back Panel.jpg (79.09 KiB) Viewed 1714 times
and found the Y axis motor, I moved the table back into the centre of travel by using a 10mm spanner on the belt pulley nut...
Y Belt.jpg
Y Belt.jpg (128.09 KiB) Viewed 1714 times
Thanks for your help!
by jamesgates1000
Thu 08 Oct , 2015 22:26 pm
Forum: Cyclone
Topic: Cyclone with 300 and 438 alarms
Replies: 14
Views: 6118

Re: Cyclone with 300 and 438 alarms

I have replaced the batteries, this has cleared the battery alarms but I am left with... 401 SERVO ALARM :X AXIS VERDY OFF 438 X AXIS:INV. ABNORMAL LOAD 300 APC ALARM : X AXIS NEED ZRN 300 APC ALARM : Z AXIS NEED ZRN I guess I will need to reset the reference position to clear the two 300 alarms. Do...
by jamesgates1000
Thu 08 Oct , 2015 22:23 pm
Forum: Triac
Topic: Fanuc Triac Overtravel Alarm
Replies: 4
Views: 1735

Re: Fanuc Triac Overtravel Alarm

Thanks, I will give that a go tomorrow when I get to my workshop.

Do you know if it is possible to move the table manually?
by jamesgates1000
Thu 08 Oct , 2015 14:43 pm
Forum: Denford Classifieds
Topic: WANTED - fanuc triac levelling pad and buttons
Replies: 1
Views: 1909

Re: WANTED - fanuc triac levelling pad and buttons

I have sourced a replacement green button and rewired the keyed swiches to enable program edit.

Still looking for one levelling pad though!
by jamesgates1000
Thu 08 Oct , 2015 14:35 pm
Forum: Triac
Topic: Fanuc Triac Overtravel Alarm
Replies: 4
Views: 1735

Fanuc Triac Overtravel Alarm

Hi I have recently bought a Fanuc Triac Machine, I have it all connected in my workshop but am unable to home it. When I turned I have a Y overtravel alarm. The table does seem very far forward. I have tried using the axis override button but it does not clear the 'not ready' flashing on the screen ...
by jamesgates1000
Thu 24 Sep , 2015 12:32 pm
Forum: Denford Classifieds
Topic: WANTED - fanuc triac levelling pad and buttons
Replies: 1
Views: 1909

WANTED - fanuc triac levelling pad and buttons

Hi,

Wondered if anyone can help, i have a denford triac and cyclone. Both are missing the key to turn off program lock.
Has anyone got a spare lock and key i can replace mine with. Also looking for a fanuc green push button for atc rotate and one of the rubber levelling pads.

Thanks
by jamesgates1000
Tue 22 Sep , 2015 20:55 pm
Forum: Cyclone
Topic: Cyclone with 300 and 438 alarms
Replies: 14
Views: 6118

Cyclone with 300 and 438 alarms

I recently bought a cyclone, it has been in storage for a while so i wasnt expecting it to start up without throwing up a few errors. Turned it on for the first time today and it showed many errors... 401 SERVO ALARM :X AXIS VERDY OFF 438 X AXIS:INV. ABNORMAL LOAD 300 APC ALARM : X AXIS NEED ZRN 300...
by jamesgates1000
Thu 03 Sep , 2015 14:17 pm
Forum: Triac
Topic: Looking for power info for Fanuc VMC Triac
Replies: 2
Views: 1452

Re: Looking for power info for Fanuc VMC Triac

Thanks for the info, yet to plug the machines in. Just got them off the pallets, hopefully switch them on early next week.
by jamesgates1000
Fri 21 Aug , 2015 11:52 am
Forum: Denford Classifieds
Topic: Cyclone power chuck wanted
Replies: 4
Views: 2192

Re: Cyclone power chuck wanted

Hi, thanks for the quick reply. Didnt expect that! I have just invested in a couple of denford machines, still in the process of getting my workshop wired up to power them, havent had a chance to open the lathe up and have a look at what mounting it is yet. A power chuck would really help with some ...
by jamesgates1000
Tue 18 Aug , 2015 20:50 pm
Forum: Denford Classifieds
Topic: Cyclone power chuck wanted
Replies: 4
Views: 2192

Cyclone power chuck wanted

If anyone has an cyclone power chuck for sale please let me know. Cheers james
by jamesgates1000
Mon 03 Aug , 2015 19:24 pm
Forum: Triac
Topic: Looking for power info for Fanuc VMC Triac
Replies: 2
Views: 1452

Looking for power info for Fanuc VMC Triac

Hi, I have just bought a 1997 Triac VMCwith toolchanger and Fanuc O-M control, the serial number is 70826B. It will be delivered this week and I wondered if anyone has a data sheet or information on how much power it will draw. This is the information from the plate on the machine... Voltage 415V F....