Search found 24 matches
- Thu 24 Dec , 2020 10:28 am
- Forum: Suggestions and Feedback
- Topic: More support
- Replies: 2
- Views: 20212
More support
Can I suggest the staff at Denford are more active on your (this) site I'm reading a lot off posts with no answers
- Sun 13 Dec , 2020 15:12 pm
- Forum: QuickCAM 3D/PRO/4D
- Topic: 2 part machining
- Replies: 0
- Views: 8609
2 part machining
Hi
I want to machine 2 holes (for fixing) in my work piece before cutting the rest out. Cutting is with Waterline Milling which I assume is outline cutting only.
How would I go about setting this up?
QuickCam Pro v1.22.0.61
VRmilling v5.66.0.0698
Microrouter v4
Thanks
Ian
I want to machine 2 holes (for fixing) in my work piece before cutting the rest out. Cutting is with Waterline Milling which I assume is outline cutting only.
How would I go about setting this up?
QuickCam Pro v1.22.0.61
VRmilling v5.66.0.0698
Microrouter v4
Thanks
Ian
- Fri 11 Dec , 2020 11:02 am
- Forum: VR Milling - All Versions
- Topic: Trouble with 1st run
- Replies: 1
- Views: 6796
Re: Trouble with 1st run
Turns out it only happens in VR mode
- Mon 07 Dec , 2020 9:44 am
- Forum: VR Milling - All Versions
- Topic: Trouble with 1st run
- Replies: 1
- Views: 6796
Trouble with 1st run
Hi all
I have loaded a model (.fnc) and trying to set the work piece offset but not having any look.
Attached a video for you to see.
I have loaded a model (.fnc) and trying to set the work piece offset but not having any look.
Attached a video for you to see.
- Sat 10 Oct , 2020 14:25 pm
- Forum: MicroRouter
- Topic: Vaccum pump blower
- Replies: 2
- Views: 7228
Re: Vaccum pump blower
Will post when I try it out, just need to get a good v point cutter with a 45 degree angle
- Fri 09 Oct , 2020 7:15 am
- Forum: MicroRouter
- Topic: Vaccum pump blower
- Replies: 2
- Views: 7228
Vaccum pump blower
Hi all
Just finished converting the vacuum pump into a swarf blower for machining aluminium
Just finished converting the vacuum pump into a swarf blower for machining aluminium
- Wed 02 Sep , 2020 6:49 am
- Forum: MicroRouter
- Topic: Vacuum pump
- Replies: 8
- Views: 11175
Re: Vacuum pump
Yer tried it with the mat and still not strong enough.
Have all the fittings for cleaner to run it, just need to cut a 63mm hole in the body to mound the port in
Have all the fittings for cleaner to run it, just need to cut a 63mm hole in the body to mound the port in
- Tue 01 Sep , 2020 18:24 pm
- Forum: MicroRouter
- Topic: Vacuum pump
- Replies: 8
- Views: 11175
Re: Vacuum pump
Little hard to see but this is the label on the side
- Tue 01 Sep , 2020 18:20 pm
- Forum: MicroRouter
- Topic: Vacuum pump
- Replies: 8
- Views: 11175
Re: Vacuum pump
Ok thanks for the reply
My bad should read the gauge better it is 12.5inHg
Pump is 115v
Had the pump in bits and everything look ok but I’m no expert
I’m guessing it’s the one that came with the machine.
Will get the spec off the pump later this evening
My bad should read the gauge better it is 12.5inHg
Pump is 115v
Had the pump in bits and everything look ok but I’m no expert
I’m guessing it’s the one that came with the machine.
Will get the spec off the pump later this evening
- Tue 01 Sep , 2020 6:38 am
- Forum: MicroRouter
- Topic: Vacuum pump
- Replies: 8
- Views: 11175
Vacuum pump
Hi
Can anyone tell me what my pump should be pulling?
I am only getting 12.5psi
Can anyone tell me what my pump should be pulling?
I am only getting 12.5psi
- Thu 23 Jul , 2020 7:00 am
- Forum: MicroRouter
- Topic: Advice
- Replies: 17
- Views: 16671
Re: Advice
Been looking for a vacuum bed but the Trend one used are no longer made so Im looking for a suitable alternative with out busting the bank, came across this
https://www.vacuumtables.co.uk/st-serie ... -vt5030-st
Theres 2 pipes going to it (not sure why) would it be suitable ?
https://www.vacuumtables.co.uk/st-serie ... -vt5030-st
Theres 2 pipes going to it (not sure why) would it be suitable ?
- Thu 23 Jul , 2020 6:53 am
- Forum: MicroRouter
- Topic: Micro Router 2nd Hand
- Replies: 92
- Views: 79378
- Mon 20 Jul , 2020 21:48 pm
- Forum: MicroRouter
- Topic: Advice
- Replies: 17
- Views: 16671
Re: Advice
Thanks Pete
- Sun 19 Jul , 2020 18:28 pm
- Forum: MicroRouter
- Topic: Advice
- Replies: 17
- Views: 16671
Re: Advice
Cannot thank Pete enough for all his help today.
Your a true star
Your a true star
- Sat 18 Jul , 2020 12:50 pm
- Forum: MicroRouter
- Topic: Advice
- Replies: 17
- Views: 16671
Re: Advice
Thanks Pete
Makes sense why I can't turn the motor by hand
Makes sense why I can't turn the motor by hand
- Sat 18 Jul , 2020 10:14 am
- Forum: MicroRouter
- Topic: Advice
- Replies: 17
- Views: 16671
Re: Advice
Anyone know if the z axis motor as been modified?
Don’t show the extra part on top in the manual
Don’t show the extra part on top in the manual
- Fri 17 Jul , 2020 17:09 pm
- Forum: MicroRouter
- Topic: Advice
- Replies: 17
- Views: 16671
Re: Advice
Hi Pete
Have sent you some PM's
Unsure is your not receiving them or your just too busy?
Ian
Have sent you some PM's
Unsure is your not receiving them or your just too busy?
Ian
- Wed 15 Jul , 2020 18:13 pm
- Forum: MicroRouter
- Topic: Advice
- Replies: 17
- Views: 16671
Re: Advice
Don’t look bad
- Wed 15 Jul , 2020 16:26 pm
- Forum: MicroRouter
- Topic: Advice
- Replies: 17
- Views: 16671
Re: Advice
Thanks Pete
Already removed from the machine, Will check them when I get home
Already removed from the machine, Will check them when I get home
- Wed 15 Jul , 2020 7:07 am
- Forum: MicroRouter
- Topic: Advice
- Replies: 17
- Views: 16671
Re: Advice
Not sure if it’s a newer motor or not but this is the motor on it