Search found 7 matches
- Thu 11 Feb , 2016 13:34 pm
- Forum: Orac
- Topic: Orac Spindle Sensor
- Replies: 11
- Views: 15679
Re: Orac Spindle Sensor
Well.. like I said: "unless I am missing something" :) Thanks for pointing my error out, it makes sense now. A couple of other questions if I may: -I see some photos where the chuck has some protective cover right behind it. Some short round tubing painted in Denford green and black stripes. My Orac...
- Wed 10 Feb , 2016 22:47 pm
- Forum: Orac
- Topic: Orac Spindle Sensor
- Replies: 11
- Views: 15679
Re: Orac Spindle Sensor
Well, I haven't measured the pulley reduction, but if the VFD goes up to 87Hz, the motor should spin at (87 / 60) * 1400 = 2030RPM. The spindle pulley being larger then the motor pulley, it would still not hit 2000RPM at the chuck. Unless I am missing something.
- Wed 10 Feb , 2016 14:42 pm
- Forum: Orac
- Topic: Orac Spindle Sensor
- Replies: 11
- Views: 15679
Re: Orac Spindle Sensor
How exactly does the Orac spindle get to 2000RPM if the motor is only 1400RPM? Not to mention the pulley reduction.
- Wed 10 Feb , 2016 6:56 am
- Forum: Orac
- Topic: Orac Spindle Sensor
- Replies: 11
- Views: 15679
Re: Orac Spindle Sensor
Hi, I am using probably the cheapest BOB you can buy. It looks just like this one: http://www.ebay.com/itm/CNC-5-Axis-Interface-Breakout-Board-For-Stepper-Motor-Driver-CNC-Mill-MACH3-DX-/251728061990?hash=item3a9c296626 A poorly written manual can be found here, if you need an overview: https://www....
- Tue 09 Feb , 2016 7:58 am
- Forum: Orac
- Topic: Orac Spindle Sensor
- Replies: 11
- Views: 15679
Re: Orac Spindle Sensor
I still have the original drivers and they were working in the original setup. However, as I read on some other thread in here, they don't take 5V signals for step/dir. At this moment the Orac is running using some TB6600 based drivers. These don't provide the expected amps and only go up to 40V as ...
- Sun 07 Feb , 2016 10:38 am
- Forum: Orac
- Topic: Orac Spindle Sensor
- Replies: 11
- Views: 15679
Orac Spindle Sensor
Hello,
Has anybody managed to use the original spindle sensor(s) on the Orac for a Mach3 conversion? I would need to know what voltage they need to be powered at and if that PCB next to the spindle will output 5V signals for my BOB.
Thanks
Has anybody managed to use the original spindle sensor(s) on the Orac for a Mach3 conversion? I would need to know what voltage they need to be powered at and if that PCB next to the spindle will output 5V signals for my BOB.
Thanks
- Thu 28 Jan , 2016 8:51 am
- Forum: Orac
- Topic: Denford Orac Conversion
- Replies: 0
- Views: 9754
Denford Orac Conversion
Hello, I just purchased a Denford Orac and I am trying to convert it to more modern electronics. Before I tear it apart, is there anything that can be reused? Such as the drivers: do they take common step/dir signals so that I can use them with a parallel port breakout board? The VFD: can it be cont...