Search found 82 matches

by -=PAB=-
Mon 19 Oct , 2009 13:52 pm
Forum: Denford Classifieds
Topic: 2000 TRIAC PC CNC MILLING MACHINE FOR SALE ON EBAY
Replies: 0
Views: 2197

2000 TRIAC PC CNC MILLING MACHINE FOR SALE ON EBAY

2000 TRIAC PC FOR SALE ON EBAY ITEM NO. 140353303538


excellent condition. comes with laptop and vr milling 2.3 plus loads more tools etc...
by -=PAB=-
Sat 06 Dec , 2008 1:02 am
Forum: VR Milling - All Versions
Topic: how can i reduce pauses between programme lines
Replies: 13
Views: 9773

its the x axis. backlash is fine. would not tightening the gib strip increase the chance of stalling?? extra stress on motor?? how do i know which is the z drive. my electrical is skill is minimal. how do i check the current? feedrate max is 1000 but this program is cutting at 150- rapid 1000. cheer...
by -=PAB=-
Fri 05 Dec , 2008 19:24 pm
Forum: VR Milling - All Versions
Topic: how can i reduce pauses between programme lines
Replies: 13
Views: 9773

the pic

picture shows the engraving done with turbo and without - machining the same program notice the difference! i dont think its the gibs or motor sticking- checked the gibs and belt tension. its so closely machined and it still happens. think it must be software???? the euro card and axis drive were ta...
by -=PAB=-
Wed 03 Dec , 2008 21:14 pm
Forum: VR Milling - All Versions
Topic: how can i reduce pauses between programme lines
Replies: 13
Views: 9773

contour

the Shortest Contour is set at 0. eprom is mint 2.1. cant understand why its fine when not using turbo. even in simple bigger moves it loses posistion. the battery in my eurostep card has been removed due to corrosion could this be the answer- no damage was done to the card though. will post pic asa...
by -=PAB=-
Tue 02 Dec , 2008 0:17 am
Forum: VR Milling - All Versions
Topic: how can i reduce pauses between programme lines
Replies: 13
Views: 9773

already using that version - no difference.
by -=PAB=-
Mon 01 Dec , 2008 20:21 pm
Forum: VR Milling - All Versions
Topic: how can i reduce pauses between programme lines
Replies: 13
Views: 9773

problem with turbo mode

when i run an engraving program with turbo mode activated posistion of the letters are not in line. running the same program with turbo mode deactivated its fine??? why?? what can i do to make it run under turbo mode and still get the accuracy??


any help would be much appreciated. thanks.
by -=PAB=-
Fri 21 Nov , 2008 19:13 pm
Forum: VR Milling - All Versions
Topic: how can i reduce pauses between programme lines
Replies: 13
Views: 9773

how can i reduce pauses between programme lines

is it possible to reduce the slight dwell between programm lines while machining? i am using vr milling 2.3 on a triac pc (2000)
by -=PAB=-
Wed 12 Nov , 2008 23:52 pm
Forum: Post Processors
Topic: FEATURECAM POST PROCESSOR REQUIRED
Replies: 1
Views: 11158

FEATURECAM POST PROCESSOR REQUIRED

ANYONE WHO HAS A GOOD WORKING POST PROCESSOR FOR DELCAM FEATURECAM I WOULD BE GRATEFUL IF THEY COULD POST IT.

MANY THANKS.
by -=PAB=-
Sun 02 Nov , 2008 12:07 pm
Forum: Denford Classifieds
Topic: WANTED - EURO STEP CONTROL CARD
Replies: 0
Views: 1969

WANTED - EURO STEP CONTROL CARD

eurostep control card normally found in triac pc's or vmc's needed urgently.

many thanks.
by -=PAB=-
Fri 31 Oct , 2008 16:23 pm
Forum: Downloads
Topic: 2000 TRIAC PC ELECTRICAL DRAWINGS WANTED
Replies: 0
Views: 2703

2000 TRIAC PC ELECTRICAL DRAWINGS WANTED

need all electrical drawings available.

thanks..
by -=PAB=-
Fri 31 Oct , 2008 16:14 pm
Forum: Triac
Topic: X AXIS PROBLEM ON 2000 TRIAC PC
Replies: 8
Views: 6198

checked card in and ribbon cable

i have checked the cards are seated and ribbon cables are attached properly. i have swapped over the wires to the y axis with the x. the x then works fine. so its not the card as i have swapped the Y axis card with the x and it still does not work, its not the motor, its not the pcb board as i have ...
by -=PAB=-
Sun 26 Oct , 2008 19:10 pm
Forum: Denford Classifieds
Topic: WANTED TRIAC VMC SPARE
Replies: 0
Views: 2002

WANTED TRIAC VMC SPARE

anything considered
by -=PAB=-
Sun 26 Oct , 2008 13:45 pm
Forum: Electronics
Topic: WHAT DOES THE BATTERY ON THE EUROSTEP CONTROLLER DO?
Replies: 7
Views: 6210

WHAT DOES THE BATTERY ON THE EUROSTEP CONTROLLER DO?

WHY IS IT NEEDED AND WILL THE MACHINE FUNCTION WITHOUT IT?

WHERE CAN I GET A REPLACEMENT AS MINE HAS LEEKED?
by -=PAB=-
Sun 26 Oct , 2008 13:40 pm
Forum: Triac
Topic: X AXIS PROBLEM ON 2000 TRIAC PC
Replies: 8
Views: 6198

x axis fault

i just fool the machine into thinkin its datumed it does not actually move. the motor does not turn- checked the fuses- on card and main board. no problem- even swapped the axis card with one i know works- still nothing. vr milling shows it moving in x axis but it does not. dont know how to check th...
by -=PAB=-
Sat 25 Oct , 2008 21:41 pm
Forum: Triac
Topic: X AXIS PROBLEM ON 2000 TRIAC PC
Replies: 8
Views: 6198

i can activate and datum it manualy but get no movement at all from the x axis. i am using Vr milling 2.3
by -=PAB=-
Sat 25 Oct , 2008 17:09 pm
Forum: Triac
Topic: X AXIS PROBLEM ON 2000 TRIAC PC
Replies: 8
Views: 6198

X AXIS PROBLEM ON 2000 TRIAC PC

the x axis is not working- tried changing the axis control card- no diffferent. when checking the x datum switches notice 2 blue wires appear to have been cut by the previous owner(note pic) could this be the problem? also i have had to remove the battery from the eurostep controller card as it was ...
by -=PAB=-
Mon 20 Oct , 2008 18:23 pm
Forum: Denford Classifieds
Topic: WANTED TRIAC PC SPARES
Replies: 0
Views: 1970

WANTED TRIAC PC SPARES

looking for control boards, axis drives, emergency stop switch, rs232 cable, eurostep controller etc.

please let me know what you have.

mant thanks. :D
by -=PAB=-
Wed 15 Oct , 2008 20:12 pm
Forum: Denford Classifieds
Topic: WANTED VR MILLING V2 for TRIAC PC
Replies: 2
Views: 2775

how much do you want? it is old software dont know why its not free.
by -=PAB=-
Tue 14 Oct , 2008 23:12 pm
Forum: Denford Classifieds
Topic: WANTED VR MILLING V2 for TRIAC PC
Replies: 2
Views: 2775

WANTED VR MILLING V2 for TRIAC PC

need registration key. will buy
by -=PAB=-
Mon 13 Oct , 2008 17:12 pm
Forum: Denford Classifieds
Topic: easy change tooling required
Replies: 1
Views: 2510

easy change tooling required

if you want to sell, please let me know.